BioDur Carpenter CCM Alloy is a non magnetic cobalt chrome alloy with high strength, corrosion and wear resistance. This is a vacuum induction melted and electroslag remelted alloy (ESR).

Single Figures are Maximums

Specifications:

UNS R30075, Co-28Cr-6Mo, ASTM F799, ASTM F1537, ISO 5832-4, ISO 5832-12

Material is equivalent to ASTM F1537 Alloy #1

Applications:

Orthopedic Implants, ebdoprotheses and osteosynthesis implants,

Hastelloy C22, also known as Alloy C22 is very similar to Hastelloy C276 and has good heat resistance and corrosion resistance. This material has resistance to pitting, stress corrosion cracking and crevice corrosion.

Both Hastelloy C22 and C276 are used in pollution control, chemical processing, waste treatment and seawater applications. There is little difference between the two alloys in corrosion resistance ability except for one process: Hastelloy C22 shows an improvement over Hastelloy C276 when it is used in certain saturated wet chlorine environments. However, C276 is used more due to supply and availability.

Hastelloy C22 has better overall corrosion resistance than other nickel based alloys available today, including Hastelloy C276 and Hastelloy C4 alloy and Inconel 625. C22 contains 22% chromium, whereas C276 contains 16%, which is one factor contributing to C22 improved performance.

Specifications:

UNS N06022, ASTM B574, ASTM B575, ASME B564,

Applications:

Oil and gas applications, Acetic acid, acid etching, flue gas scrubber systems, nuclear fuel reprocessing, pickling systems, plate heat exchangers, tubular heat exchanges, chlorination systems, incineration scrubber systems, waste water processing.

MP35N alloy is a non-magnetic, nickel-cobalt-chromium-molybdenum alloy with a unique combination of ultrahigh tensile strength (up to 300 ksi [2068 MPa]), good ductility and toughness, and excellent corrosion resistance. In addition, this alloy displays exceptional resistance to sulfidation, high temperature oxidation, and hydrogen embrittlement. In seawater environments, this alloy is immune to general, crevice and stress corrosion.

MP35N resists corrosion in chloride solutions such as hydrogen sulfide, salt water, and also mineral acids.

The unique properties of MP35N alloy are developed through work hardening, phase transformation and aging. If the alloy is used in the fully work hardened condition, service temperatures up to 750°F (399°C) are suggested.

Specifications:

UNS R30035 NACE MR0175

AMS 5758 Bar, MP-35N BAR
Vacuum Induction Plus Consumable Electrode Vacuum Melted
Solution Heat Treated for Work Strengthening.

AMS 5844 Bar, MP35N ROUND BAR
Vacuum Induction Plus Vacuum Consumable Electrode Vacuum Melted
Solution Heat Treated and Work Strengthened.

AMS 5845 Bar, MP35N ROUND BAR
Vacuum Induction Plus Consumable Electrode Vacuum Melted
Solution Heat Treated, Work Strengthened and aged ASTM F-56

Applications:

Fasteners, springs, pacing leads, stylets, catheters, orthopaedic cables, nonmagnetic electrical components and instrument parts in medical, seawater, oil and gas well, and chemical and food processing environments.

C792 Leaded Nickel Silver has good formality, good corrosion and tarnish resistance.

Specifications:

UNS C79200, ASTM B151 (bar), ASTM B206 (wire)

Applications:

Lock pins for builders hardware, electrodes, medical EKG, decorative items, jewelry, musical instrument valves and components, optical instrument components, fittings for food and dairy equipment, screws, rivets, slide fasteners, lighnting protection, heating equipment, cooling equipment.

H13 Tool Steel is a versatile chromium-molybdenum hot work steel has good thermal shock resistance and thermal fatigue cracking. H14 is able to handle some water cooling while in service. H13 ESR (electroslag remelting) has greater homogeneity and superior fine structure, which leads to improved machinability, polishability and high temperature tensile strength.  Alloy H13 has high hardenability, excellent wear resistance and hot toughness.

H13 has good toughness and good stability in heat treatment. This is available as ESR and in VAR (vacuum-arc-remelted) also.

Specifications:

UNS T20813, ASTM A6811, FED QQ-T-570,

Applications:

Hot work applications, pressure die casting tools, extrusion and forging tools, hot shear blades, stamping die and plastic molds. Inserts, cores. Components that require high toughness and excellent polishability.

Flats – Rounds – Squares – Hollowbar
Standard Sizes – Non-Standard Sizes – Metric Sizes

High resistance to heat checking.
Excellent resistance to thermal shock.
Good size stability.
Good red hardness.

Data is typical and should not be construed as actual values for any catagory.
Applications and technical information require engineers and tool designers to exercise independent judgement

M2 is a very popular grade of high speed steel and has excellent toughness, wear resistance and red hardness properties.

This material also comes in a M2 ESR version.

Applications:

Miller Cutters, gear cutters, blanking dies, boring and twist drills, punches, reamers, mandrels, center drills, thread chasers, router bits, lathe tools, shear broaches, taps, blades, wood knifes, taps.

Advantages:

Very high red hardness, high hardening response, outstanding wear resistance.

Data is typical and should not be construed as actual values for any catagory. Applications and technical information require engineers and tool designers to exercise independent judgement

C64200 Silicon Aluminum Bronze is an excellent alloy when your applications requires the strength and anticorrosive abilities that comes from an aluminum bronze alloy but when you need the ease of machinability of a bearing bronze alloy. C642 is a very popular alloy due to its machinability rating of 60 with a tensile strength range from 75-90 KSI.

Next Generation Metals has this available in rod and bar in hexagon, round and square.

Tempers available are M10, M30, H04, O50, HR50,

Specifications:

UNS C64200, CDA 642, AMS 4631, AMS 4634, ASTM B-124, ASTM B-150, ASTM B-249. ASME SB-150. QQ-C-465, SA J463, SAE J461

Applications:

Cams, strut bushings, gears, marine hardware, fasteners, landing gear parts, landing gear bushings and bearings, valve guides, corrosion resistant parts, propeller hubs, shafts, sleeves, rock bit bearing bushings, wellhead components, bolts, nuts, valve stems, valve components, automobile engine cam parts, safety belt assemblies, valve and pump components, hooks, valve stems, hardware, pins, valve guides, pole line hardware.

Custom 455 is a martensitic age-hardening stainless steel that has higher strength and hardness capability when compared to Custom 450 stainless. Its hardness capability is approximately HRC 50. Custom 455 has good corrosion resistance to atmospheric environment coupled with ease of fabrication.

Custom 455 is also known as XM-16.

Specifications:

• UNS S45500
• AMS 5617
• AMS 5578 (welded tube)
• AMS 5860 (sheet, strip, plate)
• MIL-S-83311
• ASTM A564
• ASTM F899
• ASME SA-564
• ASTM A693
• Boeing HMS-6-1093

Capable of ASTM A-564 XM-16

Also known as Grade XM16

Alloy 455 Condition Annealed: Rc Hardness 31

Alloy 455 Condition H900: Rc Hardness 49

Alloy 455 Condition H950: Rc Hardness 48

Alloy 455 Condition H1000: Rc Hardness 45

Alloy 455 Condition H1050: Rc Hardness 40

Applications:

Medical instruments, small turbine engine shafts, extruder screws.

Stainless Steel Grade 422 is a hardenable martensitic stainless steel which is being widely used for high temperatures up to 1200°F. It has excellent creep-rupture properties in the range of 600/1200°F and is capable of being heat treated to various high strength levels depending on section, form, and application involved.

Type 422 offers designers in the aircraft and power industries high strength/weight ratios from room temperature to 1200°F. The composition is carefully balanced to provide a microstructure which is virtually all tempered martensite after heat treatment. This structure assures uniformity of mechanical properties with a minimum of directionality.

Specifications: 

UNS S42200, AISI 616, AMS 5655. B50A951. GE B50A125E, SAE 51422, AISI 422; M-8663; ASTM A 565. PDS 10705 AJ

Applications:

Aircraft parts, steam and gas turbine components, high heat components, rotors, thermal engines components, power plant components, turbine blades, bolting.

316LVM F-138 is regarded as the ‘Medical Stainless Steel Grade’. This stainless steel 316 Vacuum Arc-Remelted (VAR) to achieve the extremely high levels of purity and ‘cleanliness’ required for surgical implants. It has excellent resistance in physiological environments, to general and intergranular corrosion, to pitting and crevice corrosion.

The ASTM F138 specification signifies implant grade. It is mainly used for permanent implants. 316LVM corrosion resistance is improved by a reduced carbon content compared to the 300 series alloy grades.

316LVM is centerless ground and has a highly polished appearance.

Specifications:

Grade 316 Stainless Steel  is the standard molybdenum-bearing grade. The molybdenum gives 316 better overall corrosion resistant properties than Grades 302 and 304, particularly higher resistance to pitting and crevice corrosion in chloride environments. It has excellent forming and welding characteristics. It is readily brake or roll formed into parts for applications in the industrial, architectural, and transportation fields. Grade 316 also has outstanding welding characteristics.

Grade 316L is low carbon version of 316 and is immune from sensitization (grain boundary carbide precipitation) so it can be used in heavy gauge welded components (over about 6mm).

Grade 316H has a higher carbon content and is used at elevated temperatures, as does stabilized grade 316Ti.

The austenitic structure also gives these grades excellent toughness, even down to cryogenic temperatures.

Specifications:

UNS S31600,

UNS S31603 (316L),

UNS S31609 (316H)

AISI 316, ASTM A-276, ASTM A-240, ASTM A-409, ASTM A-480, ASTM A-666, ASME SA-240, ASME SA-480, ASME SA-666, ASTM A-262.

Applications:

Food preparation equipment, laboratory benches and equipment, boat fittings, components for mining, quarrying ad water filtration, chemical containers, heat exchangers, threaded fasteners, springs,

Forms:

Bar, rod, plate, sheet, coil, strip, tube, pipe

316, 316L, 316H stainless steel

In this high strength alloy, the molybdenum content increases resistance to marine environments, Grade 316B has high creep strength at high temperatures and good heat resistance.

Specifications:

UNS S31600, 316B, 316 Condition B, 316 Vac Melt, AISI 316, MIL-S-7720A, QQ-S-763, ASTM-A-276, ASTM-A-479, AMS-S-7720, ASTM-A-193

Applications:

Food and pharmaceutical processing equipment, marine exterior trim, surgical implants, industrial equipment that can handle the corrosive process chemicals used to produce inks, rayons, photographic chemicals, paper, textiles, bleaches, and rubber.

316 Condition B Stainless Steel

304 Condition B is a strained hardened variant of 304 Annealed. 304B has higher strength, which is achieved by cold working. This material is not heat treatable.

Specifications:

UNS S30464, QQ-S-763(E Am. 1)(F), AMS-QQ-S-763, ASTM-A-276, ASTM-A-193 Grade B8 CL2, ASTM A-887, Type 304B4,

Applications:

Fastener products, hex cap screw, studs, nuts, bolts, washers.

Stainless grade 304 is produced in various carbon levels. We stock T304, T304L (low carbon) and T304H (high carbon) in a wide range of gauges and finishes. We also stock 304/304L Dual Certified.

304L has a maximum carbon content of .03%. 304H has a carbon content between .04% and .08%

Grade 304 is the standard “18-8” stainless. It is the most versatile and most widely used stainless steel, available in a wider range of products, forms (bar, sheet, plate, tube, coil, etc.) and finishes (Pump shaft quality “PSQ”, Centerless Ground, 2B, etc), than any other. It has excellent forming and welding characteristics. The balanced austenitic structure of Grade 304 enables it to be severely deep drawn without intermediate annealing, which has made this grade dominant in the manufacture of drawn stainless parts such as sinks, hollow-ware and saucepans, handlebar, hooks, and chains. Grade 304 is readily brake or roll formed into a variety of components for applications in the industrial, architectural, and transportation fields. It also has outstanding welding characteristics. Post-weld annealing is not required when welding thin sections.Grade 304L, the low carbon version of 304, does not require post-weld annealing and so is extensively used in heavy gauge components (over about 6mm).

Grade 304H with its higher carbon content finds application at elevated temperatures. The austenitic structure also gives these grades excellent toughness, even down to cryogenic temperatures.

These properties are specified for ASTM A240/A240M. Similar but not necessarily identical properties are specified for other products such as pipe and bar in their respective specifications.

Grade 304 cannot be hardened by thermal treatment.

Specifications

UNS S30400, Type 304: AMS 5513, ASTM A240, ASTM A666

UNS S30403, Type 304L: AMS 5511, ASTM A240, ASTM A666

UNS S30409. Type 304H

Applications:

Architectural mouldings and trim, kitchen equipment (sinks, splashbacks, saucepans, cutlery, flatware), welded components or chemical, textile, paper, pharmaceutical and chemical industry processing equipment. Also brewery, dairy, food production equipment, springs, bolts, screws, nuts, anchors.

Stainless steel grade 303 is the most readily machineable of all the austenitic grades of stainless steel.

Type 303 has mechanical properties that are comparable to both 304 and 316 stainless. The primary reason to use 303 is when you need a stainless steel with machining capabilites better than that of 304 and 316. It has roughly the same corrosion resistance as 304, but not as good as 316. The main drawback with the alloy is that it is not generally considered to be weldable. This material is hardenable by cold work.

The machineable nature of Grade 303 stainless steel is due to the presence of Sulphur in the steels composition. While the Sulphur improves machining, it also causes a decrease in the corrosion resistance and a slight lowering of the toughness. The corrosion resistance of grade 303 stainless steel is lower than that for 304. The toughness is still excellent as with other austenitic grades.

Property data given in this document is typical for bar products covered by ASTM A582. It is reasonable to expect specifications in these standards to be similar but not necessarily identical to those given in this article.

Sulphur is an addition to the composition act as initiation sites for pitting corrosion. This decreases the corrosion resistance of grade 303 stainless steel to less than that for 304. However corrosion resistance remains good in mild environments.

In chloride containing environments over 60°C, grade 303 stainless steel is subject to pitting and crevice corrosion. Grade 303 stainless is not suitable for use in marine environments.

Grade 303 stainless steel has good resistance to oxidation when intermittently exposed to temperature up to 760°C temperatures. It also has good oxidation resistance in continuous service to 870°C. This, however, is not recommended as 303 is sensitive to carbide precipitation with continuous use at 425-860°C.

Fabrication of all stainless steels should be done only with tools dedicated to stainless steel materials. Tooling and work surfaces must be thoroughly cleaned before each use, as this is necessary to avoid cross contamination of stainless steel.

Type 303 is not readily cold workable but it has excellent machinability.

Specifications:

UNS S30300, DIN 1.4305, ASTM A582, AMS 5640, ASME SA-194, ASME SA-320, ASTM A-194, ASTM A-314, ASTM A-320, ASTM A-473, ASTM A-581, ASTM A-582, MIL Spec. MIL-S-862. MIL-S-52263, QQ-S-764

Applications:

Nuts, bolts, bushings, shafts, aircraft fittings, electrical switchgear components, shafts, valve bodies, valves, valve trim, gears.

17-4 stainless steel ( Grade 630 )  is an age-hardening martensitic alloy combining high strength with the corrosion resistance of stainless steel. Hardening is achieved by a short-time, simple low-temperature treatment. Unlike conventional martensitic stainless steels, such as type 410, 17-4 stainless steel is quite weldable. The strength, corrosion resistance and simplified fabrication can make 17-4 stainless steel a cost-effective replacement for high strength carbon steels as well as other stainless grades.

Specifications:

UNS S17400, AISI 5803, AMS 5803, AMS 5825, AMS 5604, AMS 5622, AMS 5643, ASME SA-693, ASME SA-564, ASTM A-564, ASTM A-693 (Sheet, Plate, bar)

Applications: 

Inconel 625 has excellent resistance to pitting, crevice and outstanding corrosion resistance. Its Nickel content is 58.0%.

Its has outstanding high strength, excellent fabricability and corrosion resistance. Its properties make it an excellent choice for sea water applications.

Specifications:

UNS N06625, MR0175/ISO 15156, ASTM B446, AMS 5581, ASTM B444, ASTM B8219, AMS 5666, ASTM-B-443, AMS 5599, ASTM-B-446, ASTM B704, ASTM B564, AMS 5837, AMS 5666, AMS 5869, ASM B751, ASTM B7004, ASTM B705

Applications:

Components with exposure to seawater and high mechanical stresses. Oil and gas production, flare stacks on offshore oil platform, wire rope for mooring cables, propeller blades for gunboats, submarine propulsion motors, exhaust ducts for Navy boats, sheathing for undersea.

A286 is a precipitation age-hardening iron-nickel-chromium alloy that is one of the most popular and widely used of high temperature alloys. It maintains good strength with oxidation resistance at temperatures of up to 1300F. A286 is used in various components, such as aircraft and industrial gas turbines due to is high strength and superior fabrication. A286 is also very popular in offshore oil and gas industry where high levels of heat and stress are a factor.

The work hardening of A286 is equivalent to 310S Stainless, and cold working is possible at the same level.

A286 has superior corrosion resistance beyond the standard 304 and 304L. This does not change after the aging process.

A286 is harder to work with than 316 and 310 stainless, however A286 can still be cold-worked with positive results. However, compared with other high-temperature alloys A286 is much easier to machine.

A286 Solution Treated

A286 solution treated AMS 5731 (AMS 5732 capable)

Solution Heat Treatment: 1800ºF ± 25 (982 ± 14ºC) 1 hour, water/oil quench (AMS)
Hardness: ≥ 217HB or 220 HB (BS), ≥201HB (AMS)

A286 Solution Treated and Aged (1800ºF)

A286 Solution Treated and Aged is covered by specifications AMS 5732, BS HR51, ASTM A638 660 Type 2, ASTM A453 660 Class B

Solution Heat Treatment:
980ºC ± 10 for > 1 hour, followed by air cool (BS)
1800ºF ± 25 (982 ± 14ºC) 1 hour, water/oil quench (AMS)

Precipitation Heat Treatment:
720ºC ± 10 > 16 hours, followed by air cool (BS)
1300-1400 ºF (704-760ºC) hold not less 16 hours, air cool (AMS)

Hardness:
248 – 341 HB or 260 – 360 HV (BS)
248-341 HB (AMS)

Specifications:

• UNS S66286
• JIS G4312
• EN 1.4980
• EN 10204 3.1
• NACE MR0-175
• SUH 660
• AMS 5525
• AMS 5726
• AMS 5731
• AMS 5732 (formerly AMS 5735)
• AMS 5734
• AMS 5736
• AMS 5737
• AMS 5804
• AMS 5853
• AMS 5895
• API PSL 3
• ASME SA-638
• ASTM A-453 Grade 660 Class A, B, C, D
• ASTM B-638 Grade 660 Type 1, 2
• GE B50T1181
• GE B50T12
• GE B50T81

Applications:

• Jet engine components such as turbine wheels, blades, frames, casings, afterburner parts and high temperature fasteners and springs
• nonmagnetic cryogenic equipment
• Aircraft gas turbines
• offshore oil and gas industry.
• Low Temperature applications
• Gas turbine, disk, blades and shafts
• Compressors
• Fasteners
• Springs
• Superchargers
• Manifold Components
• Moderate Corrosion Applications in Aqueous Solutions
• Non-Magnetic Cryogenic Equipment

6061 aluminum bar is either a cold finished or extruded alloy with excellent corrosion resistance, workability and adequate machinability. It is a widely used heat treatable alloy.

Specifications:

UNS A96061, ASTM B211, AMS 4115, AMS 4116, AMS 4117, AMS 4128, AMS QQ-A-225/8, ASTM B221, AMS 4150, AMS 4160, AMS 4161, AMS QQ-A-200/8.

Applications:

Marine components, truck components, railroad cards, pipelines, specialty fasteners, tooling, shafts.

Tempers:

6061-T6

6061-T651

6061-T6511

Aluminum alloy 2011 is a high mechanical strength alloy that is well known for its exceptional machinability. This alloy is very common and readily available.

Specifications:

UNS A92011, ASTM B210, ASTM B211, SAE J454

Applications:

Appliance parts, automotive trim, fasteners, fittings, ordnance.

H-11 tool steel is a hot work steel that is represented by its excellent impact toughness. It consists of less vanadium than the commonly used H13 hot work tool steel. This gives it the higher toughness, with some reduction in wear resistance and temper resistance. H11 is a deep-hardening, air-hardening steel that gives minimal size change during heat treatment. It also has super resistance to thermal fatigue cracking (heat checking) and superb resistance to gross cracking and thermal shock when water cooled in service. Experts will recommend H11 for hot tooling applications where maximum resistance to cracking is required.

Specifications:

• UNS T20811
• DIN 1.2343
• AMS 6437
• AMS 6485
• AMS 6487
• AMS 6488
• ASTM A-681
• FED QQ-T-570
• SAE J437
• SAE J438
• SAE J467
• AISI 610
• ASTM A-579
• MIL-S-47262

Applications:

Hot punches, die casting dies, hot shear blades, forging dies, hot gripper dies and extrusion tooling.

H11 is used for highly stressed structural parts such as aircraft landing gear.

D2 Tool Steel is has become the tool and die standard to compare against other tool steels. It has relatively high attainable hardness and an abundant and large, chromium-rich alloy carbides in the microstructure. These carbides are what provides very good resistance to wear from sliding contact with other metals and abrasive materials. It is has good toughness, tool performance, price, and a wide variety of product forms. This is also available as an Electro-Slag-Remelted (ESR) product. The remelting process provides improved chemical homogeneity, refinement of carbide size, and the associated improvements in mechanical and fatigue properties.

Specifications:

UNS T30402, ASTM A-681, QQ-T-570, JAE J437, SAE J438.

Applications:

Rolls, punches, dies for blanking, forming, trimming, and thread rolling, shear knives, food-processing knives, and gauges. Deep drawing dies, cupping dies, forming dies, sheet metal forming rolls, shear blades for strip and sheet including flying shears, circular cutters for cold rolled strip, master tools, beading rools, wear parts, shear blades, trimmer dies, thread rolling dies, cold extrusion dies, broaches, plug gauges, ring gauges, special taps, straybolt taps, brick and tile mould liners, master hobs for cold hobbing plastic moulds and cut moulds for plastics.

Grade 2 titanium has a varied usability and a wide availability, leading many manufacturers of titanium to use this material. It has many of the same quality of Grade 1 titanium but it is slightly stronger. It has the same corrosion resistance.

Grade 2 titanium possesses strength, good weldability, ductility and formability.

Specifications

AMS-T-9046B, AMS 4900; AMS 4902, AMS 4941, AMS 4942, AMS 4951, MIL-T 9046J, ASTM B265, B337, B338, B348; ASTM F67

Applications:

Next Generation Metals is a leading distributor of stainless bar to manufacturers in the Oil and Gas Industry.

410 QDT Stainless Steel is used for petrochemical applications such as oilfield sour gas hydrogen sulfide (H2S) services. This material is double tempered to relieve internal stresses and it also guarantees that no untempered martensite remains in the bar. The 410 QTD is certified with a minimum yield strength of 80 KSI and a hardness of RC22 max. This is in compliance with standards set for H2S-containing environments, NACE MR0175 and/or MR0103. The 410 QDT stainless grade also meets AP1 6A standards, making it optimal for resisting corrosion during petrochemical applications such as sour gas H2S services.

Materials are manufactured and certified to the latest revision of these following specifications:

Specifications:

Specifications:

• ASTM A484, ASTM A564
• AMS 5643, API 6A
• NACE MR0175/ISO 15156
• NACE MR0103

420 MOD (13 CR)

This corrosion resistant alloy is used in oil and gas operations in corrosive environments where other stainless or carbon pipe are not able to be used. Application are in offshore production operations.

Specifications:

• UNS 42000
• ASTM A276
• NACE MR0103
• NACE MR0175/ ISO 15156
• API 6A PSL 3

UNS Number S30323

303Se Stainless Steel is a free machining 18-8 chrome-nickel steel. Selenium, added to an 18-8 stainless steel that is tough and difficult to machine, makes it so easily and freely machinable that it can be readily be handled on automatic screw machines. It can be machined at about 75% of the speed of carbon C1212. This material has displayed nongalling properties that make disassembly of parts easy and help to avoid scratching or galling in its moving parts.

Type 303Se has somewhat better formability than Stainless Type 303 and should be considered for applications which involve cold-forming operations.

Type 303Se can been used for parts that are fabricated by machining, grinding and polishing. For example, all types of screw machine products, valves, valve trim, etc. However, it is not recommended for vessels containing gases or liquids under high pressure.

Stainless Type 303Se is resistant to atmospheric corrosion, foodstuffs, sterilizing solutions, many organic chemicals and dyestuffs, and a wide variety of inorganic chemicals.

Intergranular corrosion may be a problem if the material is heated between 800ºF (427ºC) and 1650ºF (899ºC) or cooled slowly through that range.

For optimum corrosion resistance, surfaces must be free of scale, lubricants, foreign particles, and coatings applied for drawing and heading. After fabrication of parts, cleaning and/or passivation should be considered.

Properties
Physical Properties
Specific Gravity
—	7.83
Density
—	0.2830	lb/in³
Mean Specific Heat
32 to 212°F	0.1200	Btu/lb/°F
Mean CTE
32 to 1200°F	10.4	x 10-6 in/in/°F
Electrical Resistivity
70°F	433.0	ohm-cir-mil/ft
Typical Mechanical Properties

Titanium 6Al-4V Grade 5 UNS R56400

Ti 6Al-4V titanium is used the most of all alpha-beta titanium alloys. It is usually used in the annealed condition, at service temperatures up to 750°F. However it can be heat treated to gain high strength under 4″ thick. Hardenability is limited in sizes over 1″ and may not develop full properties. Ti 6Al-4V can be welded with matching or with an ELI filler wire.

Ti 6Al-4V is generally resistant to corrosion even though it still may be quickly attacked by environments that cause breakdown of the protective oxide. These include hydrofluoric (HF), hydrochloric (HCl), sulfuric and phosphoric acids. Inhibitors are know to reduce this for all but hydrofluoric. Ti 6Al-4V resists attack by pure hydrocarbons, and most chlorinated and fluorinated hydrocarbons.

Ti 6Al-4V can have chloride stress corrosion cracking (known as SCC) in some conditions, although it is known to be among the better of the titanium alloys in this regard. Generally silver plated bolts are not used with Ti 6Al-4V as silver bonds easily with chlorine. Ti 6Al-4V is also susceptible to SCC in environments such as methyl alcohol, red fuming HNO₃, and N₂O₄. In the case of red fuming nitric acid, SCC is limited to environments containing less than 1.5% water, or more than 6% NO₂. Failure in N₂O₄ has occurred when oxygen and chlorides were present as impurities.

Specifications:

AMS 4911, AMS 4920, AMS 4928, AMS 4934, AMS 4935, AMS 4965, AMS 4967, AMS 6930, AMS 6931, AMS T-9046, AMS T-9047
ASME SB 348, ASME SB 861, ASME SB-265
ASTM B 265, ASTM B 348, ASTM B 381, ASTM B 861, ASTM F 1472
EN 3.7164, EN 3.7165
MIL-T-9046, MIL-T-9047
UNS R56400
Werkstoff 3.7164, Werkstoff 3.7165

 Applications:

Silencers, Suppressors, Aircraft turbines, Engine components, Aircraft structural components, Aerospace fasteners, High-performance automatic parts, Marine applications, Sports equipment

There are four grads of commercially pure titanium. This is the softest and ductile of them. It possesses the greatest formability, high impact touhness and excellent corrosion resistance.

Specifications:

AMS 4901, AMS 4940, MIL-T-9046J, ASTM B265, ASTM B337, ASTM 338, ASTM B367, ASTM B381, ASTM F467, ASTM F468, ASTM B348, ASME SB-34. ASTM F67,

ASME SB265 (Sheet/plate)

ASME SB-337, ASME SB-338 (Tube)

CP-2 Grade 3 has superior corrosion resistance and is ideal for the aerospace and marine applications. However, it is the least used of all the commercially pure titanium grades.

ASTM AMS 4921, MIL-T-9046, ASTM B-348

• B265 Grade 3
• B348 Grade 3
• B337 Grade 3
• B338 Grade 3
• F67 Grade 3

Ti 6Al-4V Eli is one of the most commonly used titanium alloy. Neither this or Ti-6Al has corrosion properties quite as good as CP titanium but both of these grades are corrosion resistant to be used in seawater and oxidizing acids.

6AL-4V ELI is certified to ASTM F136 and is generally known as implant grade 6-4 Titanium. It is well suited for implants and medical devices due its properties of biocompatibility, corrosion resistance, high strength and toughness.

The main difference between Ti-6Al-4V ELI (Grade 23) and Ti-6Al-4V (Grade 5) is that in ELI (Extra Low Interstitials) the maximum oxygen content is lowered to .13% which gives the material an improved toughness.

This material is low interstitial version of Ti-6Al-4V, for maximum toughness. This grade is normally used in the annealed condition.

Stress relief 900-1200°F 1 to 4 hours, air cool. Duplex anneal, bar and forgings: Solution anneal 50-100°F below the beta transus, hold 1 hour minimum, air cool. Then reheat within the range 1300-1400°F, hold 1 hour minimum, air cool. Stress – relief annealing is performed after welding.

Applications:

Aerospace, Chemical processing, cryogenics vessels, medical, orthopedic implants, dental implants, bone and joint replacement, dental root implants, surgical clips.

Specifications

AMS 4907, AMS 4930, AMS 4931, AMS 4956, AMS 6932
ASME SB 348
ASTM B 348, ASTM F136
EN 3.7164
ISO 5832-3
MIL-T-9047
UNS R56401
Werkstoff 3.7164

Hastelloy C4 (UNS N06455)

Hastelloy C4 is a nickel based alloy with improved thermal stability. The tungsten is omitted and the content of the iron is about 1%.

Hastelloy C4 performs with good ductility and corrosion resistance after aging at 650 to 1040C  due to its phenonemal high performance stability.

This material is used in a variety of chemical process environments due to its exceptional resistance. C4 has better resistance than C276 highly oxidizing media. This material is commonly used in Europe whereas C276 is widely used in the United States.

Material is supplied in the Annealed (Tensile 116 – 169 KSI) and Spring Tempered (Tensile 189 – 218 KSI) condition.

ASTM B574

ASTM B619

Hastelloy C276 UNS N10276

Hastelloy C276 is a solid solution strengthened nickel based alloy with a small amount of tungsten. C276 exhibits excellent corrosion resistance in a number of harsh environments. Industries where C276 are used in are power generation, petrochemical and chemical processing, pharmaceutical, pulp production, paper production and waste treatment.

Hastelloy C276 is the most universally corrosion resistant material commonly available today. It has suberb resistance to corrosion by seawater, also to pitting (due to Its high molybdenum content), stress-corrosion cracking and to oxidizing atmospheres.

Material cannot be hardened by heat treatment although it can be hardened by cold working.

This material is NACE MR0175 certified for oil and gas service. It is also approved as a material for construction by the ASME Boiler and Pressure Vessel Code.

Specifications

Rod, Bar, Wire and Forging Stock – ASTM B 462 (Rod, Bar and Forging Stock), ASTM B 564 & ASME SB 564 (Forgings), ASTM B 574 & ASME SB 574 (Rod, Bar and Wire), ISO 9723 (Rod and Bar), ISO 9724 (Wire), ISO 9725 (Forgings), DIN 17752, DIN 17753, DIN 17754, VdTÜV 400/12.98

Plate, Sheet and Strip – ASTM B 575/B 906 & ASME SB 575/SB 906, ISO 6208, DIN 17750, VdTÜV 400/12.98

Pipe and Tube – ASTM B 622/B 829 & ASME SB 622/SB 829 (Seamless Tube), ASTM B 626/B 751 & ASME SB 626/SB 751 (Welded Tube), ASTM B 619/B 775 & ASME SB 619/SB 775 (Welded Pipe), ISO 6207 (Seamless Tube), DIN 17751, VdTÜV 400/12.98

Welding Products- INCONEL Filler Metal C-276 – AWS A5.14 / ERNiCrMo-4, INCONEL Welding Electrode C-276 – AWS A5.11 / ENiCrMo-4

Others – ASTM B 366 & ASME SB 366 (Fittings), DIN 17744 (chemical composition)

Titanium Grade 7 UNS R52400

Grade 7 is mechanically and physically equivalent to CP3 (Grade 2), except with the addition of the interstitial element palladium. Grade 7 possesses excellent weldability and fabricallity. It is resistant to corrosion in reducing acids, making it the most corrosion resistant of all titanium alloys.

Applications:

Chemical processing, marine industries, pollution control and production equipment components, silencers, suppressors.

Specifications

ASTM B265 (Rod, bar)

ASTM B348 (plate, sheet, strip)

Titanium Ti-3Al-2.5V Grade 9 UNS R56320

Also known as 3-2.5 Ti, this grade provides exceptional corrosion resistance to many harsh elements, such as seawater environments, salts and oxidizing acids. Grade 9 alloy is known for its weldability and formability, whether it be hot or cold.  This grade is a compromise between the ease of welding and manufacturing of the “pure” grades and the high strength of Grade 5.

This material is available in two conditions, annealed and cold worked stress relieved. Annealed has a lower tensile strength than CWSR, but has better forming capabilities. CWSR is stronger, but does not form as well as annealed.

Ti03Al-2.5V is an ideal material for applications such as aircraft and hydraulic system tubing due to its extreme lightweight. Other uses are for the manufacturing of sports equipment (tennis rackets, bicycles and golf clubs).

Specifications

AMS 4943, AMS 4944, AMS 4945, ASM-T-9046, MIL-T-9047

ASME SFA5,

ASTM B265, B338, B348, B381, B861, B862, B863

Applications:

Aircraft and hydraulic system tubing, sports equipment, silencers, suppressors, pharmaceutical and nuclear industries, subsea marine.

Titanium Grade 12 UNS R53400

Grade 12 is similar to Grade 2 and 3 except that Grade 12 has 0.3% molybdenum and 0.8% nickel which enhances its corrosion resistance. This material has an excellent rating for its high quality weldability. This material is a highly durable alloy that provides a lot of strength at high temperatures. Grade 12 titanium possesses characteristics similar to 300 series stainless steels. It can be hot or cold formed in a variety of ways which makes it useful in many applications.

Specifications

ASTM B265, B338, B348, B381, B861, B862, B863

ASME SB-338

Titanium CP-1 Grade 4

Grade 4 is the strongest of the four grades of commercially pure titanium. It has excellent corrosion resistance, good formability and weldability.

Applications:

medical, Airframe components, Cryogenic vessels, silencers, suppressors, Heat exchangers, CPI equipment, Condensor tubing, Surgical hardware, Pickling baskets

Specifications:

B265, B348, F67, F467, F468

Stellite® is a cobalt base alloy that is available in rod, electrodes wire and cobalt powder. Cobalt alloys are the most widely used wear resistant hardfacing materials available. Stellite® has  unique combination of wear resistance, strength and corrosion resistance make them adaptable to harsh environments.

Cobalt alloys are used by manufactures due to their excellent resistance and ability to handle the widest combination of wear types including adhesive wear, abrasion, erosion, contact fatigue, thermal shock, cavitation wear, corrosion and oxidation.  The degree to which the cobalt alloys retain these properties assures their unique position in the wear technology field.

Stellite® 1 is a hardfacing alloy that possesses excellent abrasion and corrosion resistance. Stellite® 1 keeps its hardness at temperatures above 760C (1400F).

This material contains a high proportion of hard, wear resistant primary carbides. This alloy is well suited to applications involving extreme low=angle erosion and severe abrasion. Stellite® 1 is more crack sensitive than the other Stellite® grades. One should be careful to minimize the cooling stresses experienced during casting and hardfacing processing.

Rockwell Hardness:

50-58 HRC

Specifications:

UNS R30001 AWS A5.21 / ASME BPVC IIC SFA 5.21 ERCoCr-C (Rod)

UNS W73031 AWS A5.21 / ASME BPVC IIC SFA 5.21 ERCCoCr-C (Wire)

UNS W73001 AWS A5.13 / ASME BPVC IIC SFA 5.13 ECoCr-C (Electrodes)

Applications:

Pump Sleeves, Rotary seal rings, wear pads, expeller screws, bearing sleeves.

Stellite® is a registered trademark of Kennametal Inc.

Stellite® 3 has a high carbon content which increased the volume fraction of carbides. Due to this, it has high abrasion and solid particle erosion resistance. Stellite® 3 also has a high tungsten content which improves its high temperature properties.

This alloy is generally considered inferior to Stellite® alloys 6 and 12 in most environments. However it has excellent resistance to oxidation like all the Stellite® alloys. It is 3 to 4 times are resistance than Stellite® alloy 6 and twice as resistance as Stellite® alloy 12.

Specifications:

UNS R30001, AWS A5.13 RCoCr-C, MIL-R-17131, SAE J775, MIL-C-15345 Alloy 22, MIL-C-24248

Hardness: HRC 48 – 63

Applications:

Surgical scissor inserts, valve seat inserts, needle holders, steel mill guide rolls, seaming rolls, sleeves, bushings, bearing balls, wear pads, burner nozzles, palm guides.

Stellite® is a registered trademark of Kennametal Inc.

Stellite® is a registered trademark of Kennametal Inc.

Inconel Alloy 718 is a high strength corrosion resistant nickel chromium material used for cryogenic temperatures up to long term service at 1200F. This alloy can be fabricated and may be welded in the annealed or precipitation (age) hardened condition.

Specifications:

UNS N07718, AMS 5596, AMS 5662, AMS 5664, AMS 5832, PWS S-5662, GE B60TF15, ASME SB 637, ASTM B637, ASTM B670, Capable of AMS 5663

Alloy 718  Inconel 718  Nickel 718

Applications:

Liquid fuel rockets, rings, casings, gas turbine engines, cryogenic tankage, instrumentations parts, springs, fasteners, high strength bolting, down hole shafting.

Stellite® 6 is a cobalt based alloy that consists of complex carbides in an alloy matrix. As discussed, cobalt is resistant to wear, galling and corrosion at high temperatures. Stellite® 6 is the most widely used of wear resistant cobalt-based alloys and exhibits good performance. It is industry standard for general purpose wear resistance applications, and has excellent resistance to many forms of mechanical and chemical degradation.  This material also remains at a high level of hardness up to 500C. It has good resistance to impact and cavitation erosion. Stellite® 6 is used in a variety of hardfacing processes and can be used with carbide tooling.

Rockwell Hardness:

36 – 45 HRC

Specifications:

AMS 5788

UNS R30006 AWS A5.21 / ASME BPVC IIC SFA 5.21 ERCoCr-A (Rod)

UNS W73036 AWS A5.21 / ASME BPVC IIC SFA 5.21 ERCCoCr-A (Wire)

UNS W73006 AWS A5.13 / ASME BPVC IIC SFA 5.13 ECoCr-A (Electrodes)

Applications:

Valve seats and gates, pump shafts and bearings, erosion shields, rolling couples.

Stellite® is a registered trademark of Kennametal Inc.

Type 304H is the high carbon version of 304 and 304L. T304H (high carbon) in a wide range of gauges and finishes. Type 304H has a carbon content between .04% and .10%

Grade 304H with its higher carbon content finds application at elevated temperatures. The austenitic structure also gives these grades excellent toughness, even down to cryogenic temperatures.

It is common for certifications of Grade 304H to be dual certified as 304/304H when the material has a higher carbon content.

These properties are specified for ASTM A240/A240M. Similar but not necessarily identical properties are specified for other products such as pipe and bar in their respective specifications.

Specifications

AMS 5513, ASME SA240, ASTM A240, ASTM A959, UNS S30400, UNS S30409

Composition

Applications:

Pressure vessels, petrochemical equipment, welded components or chemical,

C624 Nickel Aluminum Bronze is heat treatable to high strength; excellent corrosion resistance. The machinability rating for this alloy is 50.

Specifications:

UNS C62400 ASTM B150, ASME SB150. SAE J463, SAE J461

Applications:

Hydraulic bushings, support bushings, valve balls, fasteners, nuts, welding wire, drift pins, tie rods, wear plates, bushings, gears, cams, marine hardware, high strength fasteners, valve and pump components.

Stainless Steel 17-4 H1025 is a chromium copper precipitation hardening stainless steel that is used for applications that requires high strength and a moderate level of corrosion resistance. Alloy 17-4 is one of the most widely used grades that is precipitated hardening.

Stainless Steel 17-4 H1025 is heat treated at a temperature between 1015F and 1035F for a period of time of 225-255 minutes. The steel becomes softer that it is in its annealed condition after being treated at this high temperature.

Specifications:

UNS S17400 ASTM A564 Condition H1025, ASTM A388, ASTM A484, ASME SA564, AMS 5643, AMS 2303, API 6A PSl Level 3, NACE MR0175, NACE MRO 103

Applications:

Valve internal components, pump shafts, aerospace, mechanical components, turbine blades, nuclear waste casks, offshore applications, food industry, pulp industry, paper industry.

Stainless steel 17-4 H1075 has been heat treated at a temperature between 1065° F and 1085° F for 225-255 minutes. After treating the steel at a temperature of 1075° or higher, it will become softer than in the annealed form.

Specifications:

Condition A material heated 4 hours at specific temperature, and air cooled.

Applications:

Pump shafts, oil patch, aerospace.

Stainless Steel 17-4 H1150 is a chromium copper precipitation hardening stainless steel that is used for applications that requires high strength and a moderate level of corrosion resistance. Alloy 17-4 is one of the most widely used grades that is precipitated hardening.

Stainless Steel 17-4 H1150 is heat treated at a temperature between 1140F and 1160F for a period of time of 225-255 minutes. The steel becomes softer that it is in its annealed condition after being treated at this high temperature.

Specifications:

UNS S17400 ASTM A564 Condition H1150 Double Ages, ASTM A388, ASTM A484, ASME SA564, AMS 5643, AMS 2303, API 6A PSl Level 3, NACE MR0175, NACE MRO 103

Hardness: HRC 39

Applications:

Valve internal components, pump shafts, aerospace, mechanical components, turbine blades, nuclear waste casks, offshore applications, food industry, pulp industry, paper industry.

Stainless Steel 17-4 Condition HH1150 is 17-4 material that has been heat treated twice at a temperature with a range between 1140F and 1160F for a length of time of 225-255 minutes. This material will become softer than it is in the annealed condition after it is heat treated at such a high temperature.

Specifications:

UNS S17400 ASTM A564 Condition H1150 Double Ages, ASTM A388, ASTM A484, ASME SA564, AMS 5643, AMS 2303, API 6A PSl Level 3, NACE MR0175, NACE MRO 103

Tensile Strength: 135 KSI

Hardness: 33 Rc Maximum

Applications:

Suppressors, silencers, air spray guns, Bearings, Boat fittings, Castings, Dental components, Fasteners, Gears, Golf club heads, Hardware, Load cells, Molding dies, Nuclear waste casks, Precision rifle barrels, Pressure sensor diaphragm, Propeller shafts, Pump impeller shafts, Sailboat self steering systems, Springs, Turbine blades, Valves

416R Gun Barrel Steel is a low sulfur pre-hardened chromium grade stainless steel that is primarily used for precision rifle barrels. 416R Gun Barrel grade has various hardness ranges that can be tailor-made per your requirements. Barrel makers and rifle manufacturers use this grade for its consistency and high quality, as Next Generation Metals produces these bars as heat treated and stress relieved.

This material has good machinability for gun drilling and reaming, and has great polishability for uniform lapping, which is necessary for bore accuracy. Its homogeneous microstructure responds to heat treat  which give this material a uniform hardness along the length of the bar. This is necessary for accurate button rifling to precise groove dimensions. Its corrosion resistance to prevent rusting and minimize fouling. Next Generation Metals provides its 416R with a durable finish which does not pit when properly maintained. This material is 100% ultrasonic tested per ASTM E2375 and precision straightened.

Specifications:

• ASTM A370
• ASTM A484
• ASTM A582 (not S)
• ASTM E381
• AMS 2315

Hardness: Standard Hardness is 190-210 BHN but can be made to any of the following: HRC 24-28; HRC 28-32; HRC 32-36

Tensile Strength: 90-110 KSI

Applications:

• Rifle barrels
• Hunting rifles
• Tactical Rifles
• Competition Rifles
• Precision Rifle Barrels
• Gun Barrels
• Pistol Rifles.

C729 is a copper alloy that is an alternative to nickels alloys, aluminum bronze and beryllium copper. C729 has great advantages, like Its high strength, anti-galling, excellent machinability and it is also non-sparking.

Specifications By Temper

C729 CX 105: NACE MR0175/ISO 15156, ASTM B505

C729 AT 90: NACE MR0175/ISO 15156, MIL-STD-167, ASMTM B249, ASTM B251, BMS 7-373

C729 AT 110: NACE MR0175/ISO 15156, AMS 4596, MIL-S-901D, ASTM B249, ASTM B251, BMS 7-373, AMS 4598, AMS 4595

C729 TS 120U: NACE MR0175/ISO 15156, ASTM B249

C729 TS 9S: NACE MR0175/ISO 15156, ASTM B249

C729 TS 150: NACE MR0175/ISO 15156, ASTM B251, AMS 4597

Applications:

Trust washers, pump parts, aircraft bearings, aircraft bushings, drilling equipment, mining equipment

This material is an alloy similar to Ti 6-4 but 6Al-6V-2Sn has higher strength and deeper hardenability. Maximum strength of this alloy may be developed in sections of up to 2″ think.

Specifications:

UNS R56620 (also known as Ti 6-6-2)

AMS 4918, AMS 4971, AMS 4978, AMS 4979, DMS 1887, DMS 1879, DMS 2237

MIL-F-B2142

MIL-T-9046, MIL-T-81556, MIL-T-9047, AMS-T-9047

Applications::

Airframe structures, rocket engine cases, ordinance components,

6Al-2Sn-4Zr-2Mo is an alloy primarily used for its high strength and toughness, with its good creep resistance of up to 1000F. This alpha-beta titanium alloy is capable of being heat treated to high strengths in greater sections sizes than 6Al-4V. 6-2-4-2 forged material has enhanced strength, ductility and a combination of enhanced low-cycle fatigue and fatigue-crack growth resistance.

This material has forging and machining characteristics similar to those of Ti 6Al-4V. This grade is specified more frequently for aircraft engine manufacturers, as this material is the mostly used high temperature alloy in jet engine compressions and airframe structures.

Specifications:

UNS R54620 (also known as 6-2-4-2)

AMS 4919 (sheet, strip, plate)

AMS 4975 (bars, wire, rings (solution and precipitation heat treated)

AMS 4981 (bars, wire, forging (solution and precipitation heat treated)

AMS 6905 (bars, wire, forging (duplex annealed)

AMS-T-9046 (sheet, strip, plate

AMS-T-9047, MIL-T-9047 (bar)

MIL-T-9046H Type III Composition G sheet, strip, plate

AMS 4976, AMS 4979, AMS 4952, GE B50 TF22, AMS T-9047,

MIL-F-81556, MIL-F-83142, MIL-T-81915, GE B50TF21, GE C60TF7, GE B50TF33, PWA 1220,

Applications:

Compressor discs, blades, airframe structure, airframe skin, engine afterburner components, hush kits, turbine engines, seals.

Titanium Ti-15V-3Cr-3Sn-3Al solution treated and aged titanium is a strip alloy that is generally used for aircraft ducting, pressure vessels and other flat applications. You are age harden this material and it is highly cold formable. This can also be made as a foil.

Specifications:

AMS 4914E, ASTM B265

Applications:

High strength hydraulic tubing, fasteners, aerospace tankage, aircraft ducting, pressure vessels.

Grade 8 Al-1Mo-1V is a near alpha titanium alloy. This material has a high stiffness to density ratio. It has high modulus, low density and good elevated temperature tensile/yield properties. Its medium to high strength and excellent creep resistance enable to operate at temperatures of up to 455C.

Specifications:

UNS R54810, Ti-81-111

AMS 4915, AMS 4916 (sheet, plate)

AMS 4972, AMS 4973 (bar, wire)

Applications:

Fan and compressor blades (for jet engines), discs, spacers, deals, rings.

Titanium Grade 11 is extremely similar to Grade 1. The difference is that in the Grade 11 there is an addition of a tiny bit of palladium to enhance corrosion resistance. This corrosion resistance is useful to protect against crevice erosion and reducing acid in chloride environments.

This titanium grade has useful properties including optimum ductility, cold formability, useful strength, impact toughness and excellent weldability. This material is also suitable for deep drawing.

Specifications:

UNS R52250 Grade 11, ASTM Grade 11

ASTM B-265

Applications:

Chemical processing, chlorate manufacturing, desalination, marine applications, architecture, dimensional stable anodes, medical industry, marine industry, automotive parts, airframe parts.

Titanium 3Al-8V-6Cr-4Mo-4Zr is a beta wrought alloy with good ductility and high strength. This material is heat treatable to a wide range of strengths.

Specifications:

UNS R58640, ASME SB-265, ASME SB-348, AMS 4957, AMS 4958, MR0175, MIL-T-9047

Applications:

In tube form, oil and gas wells, fasteners, torsion bars, springs, foil.

Titanium 13TV-11Cr-3Al is a beta alloy wrought titanium alloy that is solution treated before aging. It has good ductility and fabrication properties, aging yields extremely high strengths and low density. This alloy is known for its excellent corrosion resistance.

Specifications:

AMS 4917, AMS 4959, AMS 6926, MIL-F-83142, MIL-T-9046, MIL-T-9047

UNS R58010

Applications:

High strength airframe components, aerospace. This material is reported to have been used in Lockheed’s SR-71 Blackbird, which was used for 85% of the structure.

Titanium 6Al-2Sn-4Zr-6Mo is a heat treatable titanium with excellent strength to 450C. This material can be supplied as either bar, wire or forgings.

Specifications:

AMS 4981, MIL-T-9047, MIL-T-9046

UNS R56260 (also known as 6-2-4-6)

Applications:

Intermediate temperature jet engine applications, blades, discs, spacers, seals, in gas turbine discs and impellers, in deep sour well components.

Monel 400 is a solid-solution nickel copper alloy (67% Nickel). This alloy is resistant to sea water and steam  at high temperatures. It is also resistant to salt and caustic solutions, and has excellent resistant to chloride ion stress corrosion cracking. Alloy 400 is known for resistance to many corrosion conditions, such as alkalies, saltwater, hydrofluoric acid and sulfuric acid.

Alloy 400 is a solid state solution alloy that can only be hardened by cold working.

Specifications:

UNS N04400, ASTM B164, QQ-N-281, BS 3075, ASTM B127 QQ-N-281,  ASME SB127 (Plate, sheet and strip), SAE AMS 4544  (Plate, sheet and strip), ASME SB164, (Rod, Bar, and Wire), ASME SB 564 (Forging) ASTM B165, ASTM B564, SAE AMS 4675, SAE AMS 4730 (Wire), SAW AMS 4731. ASTM B163, ASTM B725, ASTM B751, ASTM B775, ASTM B829, ASME SB165, ASME SB730, SAE AMS 4574.

Applications:

Feed water and steam generator tubing, brine heaters, sea water scrubbers, industrial, heat exchangers, transfer piping from oil refinery crude columns, pumps and valves in perchlorethylene, chlorinated plastics. Keys for automotive ignitions, Propeller and pump shafts. Material is used in chemical, oil and marine industries. chemical and hydrocarbon processing equipment. Gasoline and freshwater tanks,

Monel R405 is a nickel copper alloy that is a free-machining grade of Monel 400 due to its higher sulfur content. Monel 405 has the same corrosion resistance and physical properties as Monel 400 although it has a different range of mechanical properties. R405 is used mostly in automatic screw machines.

Specifications:

UNS N04405, ASME SB-164, ASTM B164, QQ-N-281, SAE AMS 4674, SAE AMS 7234, MIL-N-894, MACE MR0175.

Applications:

Meter and valve parts, fasteners, screw machine products.

Nickel X750 is an age hardenable alloy with high tensile strength and creep-rupture properties up to 1300F. This material shows excellent strength in tough environments over time.

Next Generation Metals carries X750 in NACE MRO175 sheet and bar.

Specifications:

UNS N07750, AMS 5542, AMS 5668, AMS 5598, B60A714, B50A151, MIL-N-7786, AMS 5667, ASTM-B-637. ASME SB-637, SAE AMS 5667, SAE AMS 5671, SAE AMS 5747, SAE AMS 5542, SAE AMS 5598.

Applications:

Oil and gas extraction, heat-treat fixtures, nuclear engineering, fasteners, springs, automotive components, gas turbines, rotor blades, wheels, bolts, rock-engine thrust chambers. Thrust reversers, hot-air duct systems in airframe applications.

Nickel Monel 200 is a solid solution strengthened, commercially pure wrought nickel with preferred mechanical properties. Alloy 200 also has excellent resistant to many common corrosives environments. This material si magnetic and is hardenable by cold working.

Nickel 200 will remain bright and free of discoloration when this material is heated and cooled in a reducing atmosphere.

Nickel 200 is usually dual certified as Nickel 200/201.

Specifications:

UNS N02200, ASTM B160, ASTM B162, ASTM B163, ASTM B622 ASTM B161, ASTM B366, ASTYM B564

Applications:

Food processing equipment, chemical processing, synthetic fiber products, aerospace, defense, Marine and offshore engineering, Salt Products, missile components, rocket motor cases,

For the manufacturing of sodium hydroxide, at temperature over 300F,

Reactors and vessels where fluorine is generated and reacted with hydrocarbons.

Caustic handling equipment and piping

Hastelloy Alloy B-2 is a solid solution strengthened nickel molybdenum alloy that shows significant resistance to reducing environments. Examples are hydrogen chloride gas and sulfuric, acetic and phosphoric acids. Also has excellent resistance to pitting and stress corrosion cracking but has poor corrosion resistance to oxidizing environments.

Hastelloy B-2 should not be exposed to temperatures in the 1000 – 1600°F range

Specifications:

UNS N10665, ASTM B-335, ASME SB-335, ASTM B-333, ASME SB-333, ASTM B-366, ASTM B-622 ASME SB-622, ASTM B-619, ASME SB-619, ASTM B-626 ASME SB-626.

Applications:

Chemical environments, Hydrochloric acid, chloride catalysts and other strong reducing chemicals, vacuum furnaces, resists corrosion from antimony chloride.

Nickel Monel K500 is an age hardenable alloy that brings together the corrosion resistance of Monel 400 with high strength corrosion fatigue and erosion resistance. K500 has approximately three times the yield strength of Monel 400 with double the tensile strength. Cold working before precipitation hardening will make it stronger.

Monel K500 is spark resistant  and non-magnetic to -200F.

Specifications:

UNS N05500, ASTM B865 QQ-N-286, AMS 4676

Applications:

Propeller shafts, pump shafts and valves. impellers, valve components for ships and offshore drilling, bolting, oil well drill collars, chains, cables, fasteners and springs for marine service, safety lifts and valves for oil and gas production.

Inconel Alloy 600 has good oxidation resistance at high temperatures. It high nickel content (Nickel 72.0%) allows its considerable resistance under reducing conditions. It is also resistant to corrosion by a number of organic and inorganic compounds. It is used extensively in the chemical industry for its strength and corrosion resistance.

Alloy 600 has superior mechanical properties, high strength, good workability and readily weldable.

Specifications:

UNS N06600, ASTM B166, ASME SB166, AMS 5665, ASTM B168 AMS 5540, ASTM B167, ASTM B168, ASTM B906, AMS 5540 ASTM B366, , ASTM B564, ASTM B167, ASME SB167, ASTM B163, ASME SB163, ASME SB516, ASTM B517, ASTM B775, STM B829, AMS 5580

Applications:

Thermocouple sheaths, furnace retort seals, fans, fixtures. Reactor vessels, heat exchanger tubing. Chemical nd food processing, heat treating, phenol condensers, soap manufacture.

Alloy 255 is a super duplex stainless steel that has superior corrosion resistance. Duplex has a high strength to weight ratio with superior and cavitation resistance.

Specifications:

Super Duplex Grade UNS S32550, Super Duplex A276, ASTM A479, ASTM A240

MR0175 limits hardness to HRC 28 Mac.

Applications:

chemical, marine, metallurgical, municipal sanitation, plastics, oil and gas offshore platforms, deck hardware, rudders, shafting, petrochemical, pollution control, wet phosphoric acid, paper making and metalworking industries. Propellers, shafts, pumps, bolts, fasteners, valves, incinerators, pipe, valves, wellhead equipments, subsea equipment,

Nitronic 60 is excellent high temperature properties. Alloy 600 has excellent high temperature oxidation resistance and is superior to Grade 304 Stainless. It is well known for ear and galling resistance. Its chloride pitting resistance is superior to Grade 316 Stainless.

Specifications:

UNS S21800, AMS 5848, ASME SA 193, ASME SA 479, ASTM A193, ASTM A276, ASTM A479, ASTM A314, ASTM A580

Applications:

Automotive valves, pins, marine shafts, pins and hanger expansion joints for bridges.valve stems, fastening systems, fasteners, pins and bushings, wear rails, roller bearings, pump components, chain drive systems.

Nitronic 50 (XM-19) has a combination of corrosion resistance and strength that is a bargain for this price range. Its corrosion resistance is superior that the other stainless steels. Its yield is nearly double the strength of Grades 304 and 316 stainless steel.

Specifications:

UNS S20910, XM-19, ASTM A193, ASTM A194, ASTM A479, AMS 5764, ASTM A240 AMS 5861, Alloy 22-13-5

Applications:

Automotive valves, fittings, fasteners, cables, chains, boat and pump shafting, heat exchanger parts, marine hardware, downhole rigging.

Nitronic 30 is an nitrogen strengthened, corrosion and abrasion resistant stainless steel. It has good toughness and is economical to use. It is highly impact resistant making it suitable for heavy duty applications.

Specifications:

UNS S20400, ASTM A666, ASTM A240

Applications:

Coal handling equipment, such as Coal buckets, hoppers, ore separators, barge liners, sewage treatment, trailer bedliners, chutes. automotive hose clamps, safety belt anchors, water supply and control structures.

Inconel Alloy 20 is an austenitic alloy that has maximum resistance to sulfuric acid. It has great resistance to corrosion, pitting and crevice corrosion.

This is both a stainless and nickel alloy due to its containing characteristics of both.

Specifications:

UNS N08020, MR0175, ASTM A265, ASTM B366, ATM A240, ASTM B462, ASTM B463, ASTM B464, ASTM B471, ASTM B472, ASTM B473, ASTM B474, ASTM B475, ASTM A480, ASTM B729, ASTM B729, ASTM B775, ASTM B829, ASTM B906

Applications:

Industries include the chemical, food, pharmaceutical, and plastics. Heat exchangers, mixing tanks, metal cleaning and pickling equipment, and piping. Synthetic rubber mfg equipment. Acid cleaning, petrochemical process equipment.

Stellite® 6B is an alloy with resistance to wear environments where seizing, galling and abrasion are in contention.

Specifications:

UNS N30016, AMS 5894

Applications:

Steam turbine erosion shields, high temperature bearings, furnace fan blades, valve stems, needle valves, nozzles, screw conveyors, valve parts, pump plungers.

Stellite® is a registered trademark of Kennametal Inc.

Nickel L605 (Alloy 25) is a non-magnetic cobalt alloy. It is the strongest of the formable cobalt alloys. Harness is typically BHN 250 with a BHN 275 max.

This is material is more difficult to machine than Grades 302, 304, 321 and 347 Stainless Steel.

Specifications:

UNS R30605, Haynes 25, AMS 5759, ASTM F90, GE B50T26A, AMS 5537, AMS 5759

Applications:

Turbine engine combustion chambers and afterburners. High temperature ball bearing and bearing races. Springs, Heart Valves (Medical). Jet engine parts, turbine blades, turbine rings.

Hastelloy X (Alloy X) is a superalloy with enhanced high temperature strength, oxidation resistance and fabricability.  It is resistance to stress corrosion cracking in petrochemical applications.  This material has good resistance to chloride stress corrosion cracking (SCC), it is primarily noted for heat and oxidation resistance. it also has good resistance to carburization, excellent resistance to reducing or carburizing atmospheres. Hastelloy X, also known as Alloy X, is one of the most widely used nickel base superalloys for gas turbine engine components.

Alloy X is non magnetic.

Specifications:

UNS N06002, ASTM B435, ASTM B366, ASTM B572, ASTM B619, ASTM B622, ASTM B626, ASTM B751, ASTM B775, ASTM B829, AMS 5536, AMS 5587, AMS 5588, AMS 5798C, AMS 5754, AMS 5587, AMS 5588

Applications:

Gas turbines, petrochemical, industrial furnaces, heat treating equipment, nuclear engineering, engine combustion chambers, turbine exhaust components, aircraft cabin heaters, nozzle vanes.

Inconel Alloy 601 is a general purpose material that provides resistance to heat and corrosion. It is praised for its resistance to high temperature oxidation and high mechanical strength.

Specifications:

UNS N06601, ASTM B166, ASTM B167, ASTM B168, ASTM B517

Applications:

Trays, baskets and fixtures used in heat treatments. Chemical processing, aerospace, power generation, stream superheater tube supports, anchors, radiant tubes, high velocity gas burners, insulating cans in acid production. Thermal reactors, combustion chambers.

Inconel Alloy 800 and Alloy 800H has good strength and resistance to oxidation and carburization in high temperatures.

Specifications:

UNS N08800

UNS N08810

N08811

ASTM B154

ASTM B163

ASTM B407

ASTM B408

ASTM B409

ASTM B515

Applications:

Ethylene pyrolysis

hydrocarbon cracking

cracking furnaces for vinyl chloride,

diphenol and acetic acid

Valves

Fittings and other components exposed to corrosive environments

Industrial furnaces

Heat exchangers

Pressure vessels.

Transfer piping

Catalyst tubes

Components in coal conversion plants.

Inconel Alloy 925 is a nickel based superalloy that is corrosion resistant and has high strength obtained through age hardening.

Specifications:

UNS N09925,

NACE MR0175

Applications:

Oil tubular products

tool joints

surface and downhole hardware for oil applications,

Fasteners,

shafting

Valves

Hangers,

Landing nipples

Marine and pup shafting.

7075 aluminum bar is one of the highest strength aluminum alloys and is used primarily in the aerospace industry due to is high strength, adequate machinability and improved stress corrosion control.

Specifications:

ASTM B211, AMS 4122, AMS 4123, AMS 4124, AMS 4186, AMS-QQ-2-225/9, ASTM B221, AMS 4154, AMS 4166, AMS 4167, AMS QQ-A-200/11

Applications:

Bicycle industry, aircraft, aerospace, military rifle components.

Tempers:

7075-T651

7075-T6511

7075-T7351

7075-T3511

7075-T76511

7075 aluminum drawn and extruded tubing is primarily used in the aerospace industry due to is high strength, adequate machinability, resistance welding and corrosion resistance. This alloy is used mostly by aircraft and ordnance industries due to its high strength.

Specifications:

Cold Drawn: ASTM B210, AMS WW-T-700/7,

Extruded Drawn: ASTM B221, ASTM B241, AMS 4154, AMS QQ-A-200/11

Applications:

Bicycle industry, aircraft, aerospace, military rifle components, silencers, suppressors.

Tempers:

7075-0

7075-T6

7075-T73

2024 aluminum is primarily used in aircraft applications for its high strength and good fatigue resistance.

Specifications:

Drawn Seamless: AMS WW-T-700/3, AMS 4086, AMS 4087, AMS 4088, ASTM B210

Hydraulic Tubing: AMS 4086

Extruded Tubing: ASTM B221 AMS QQ-A-200/3, AMS 4152, ASTM B241, AMS 4165, ASME SB241

Tempers:

2024-T351

2024-T3511

2024-T4

2024-T851

2024-T8511

Applications:

Aircraft components, Phillips head screw, hydraulic fittings.

This alloy is a good all-purpose alloy with good corrosion resistance, formability and medium strength.

Specifications:

Drawn Seamless Tube: AMS 4079, AMS 4080, AMS 4081, AMS 4082, AMS 4083, AMS-T-700/6, AMS-T-7081, ASME SB-210, ASTM B210, ASTM B234, ASTM B241, ASTM B429, ASTM B483, MIL-P-25995

Extruded Tube: ASTM B221, ASTM B241, AMS 4150, ASME SB241, MIL-P-25995, AMS QQ-A-200/8

Hydraulic Tubing: AMS-T-7081, MIL-T-7081, AMS 4081, 4083, ABS5151, BAMS517-001

Applications:

Tempers:

6061-0

6061-T4

6061-T6

Maraging (Vascomax) C250 is a cobalt strengthened steel with excellent mechanical properties, workability and heat treatment characteristics. It is age-hardenable, with ultra-high strength, toughness and resistance to crack propagation.

Specifications:

• UNS K92890
• AMS 6501
• AMS 6512
• AMS 6519
• AMS 6520
• ASTM A538
• MIL-S-46850D

Applications:

• Missile/rocket motor cases
• ejector systems
• slat tracks
• drive shafts
• aircraft landing gear
• munitions
• aerospace
• tooling
• high performance shafting
• fasteners.

Maraging (Vascomax) 300 is a cobalt strengthened steel with excellent mechanical properties, workability and heat treatment characteristics. It is age-hardenable, with ultra-high strength, toughness and resistance to crack propagation.

Specifications:

• UNS K93120
• AMS 6514
• AMS 6514
• ASTM A538
• MIL-S-46850D

Applications:

• Missile/rocket motor cases
• Gas centrifuges for uranium enrichment
• ejector systems
• torsion springs
• driveshafts
• aircraft landing gear
• munitions,
• aerospace
• tooling
• high performance shafting
• fasteners
• spring wire for valve springs.

Maraging (Vascomax) 350 is a cobalt strengthened steel with excellent mechanical properties, workability and heat treatment characteristics. It is age-hardenable, with ultra-high strength, toughness and resistance to crack propagation.

Specifications:

• UNS K93120
• UNS K93540
• UNS S35000
• AMS 6512
• AMS 6514
• AMS 6515
• MIL-S-46850D
• Also known as Vascomax 350

Applications:

• missile components and casings
• Use in gas centrifuges for uranium enrichment
• gears
• helicopter drive shafts
• Tooling
• Ordnance mounting blocks
• Motor sports components
• Load cells
• Landing gear
• fasteners
• industrial cutters
• rocket motor cases
• ejector systems
• torsion springs
• driveshafts
• aircraft landing gear
• aerospace
• tooling
• high performance shafting
• spring wire for valve springs.

Next Generation Metals carries this in stainless strip. It has excellent corrosion resistance and has high strength and good ductility when cold worked.

Specifications:

ASTM A666. UNS S30100. ASTM A167, ASTM A177, ASTM A554, QQ-S-766, ASTM A240, ASTM A480, ASTM A262

Annealed: AMS 5901

1/4 (Quarter) Hard AMS 5517

1/2 (Half) Hard AMS 5518

3/4 ( Three Quarter) Hard AMS 5902

Full Hard: AMS 5519

Applications:

Air frame sections, rail car structural components, trailer components, automotive wheel covers, wiper blade clips, stove element clips, toaster springs, conveyor parts.

Next Generation Metals stocks many sizes of Stainless Steel grade 416 in flat bar sizes. Our processes are saw cutting and we also provide shearing up to .500″ and plasma cutting up to 3″.

Stainless 416 is hardenable and has good corrosion resistance.

Specifications:

UNS S41600, AMS 5610, ASTM A582

Applications:

Fittings, trigger guard assemblies, gun parts, machine parts, fasteners.

Can also quote 416 Stainless steel Plate AMS 5610

Next Generation Metals is able to be your main supplier on 4150 Chrome Moly Vanadium, also known as 4150Mod.

This material is chromemoly steel, double stress relieved during production and cryogenically treated. Easily understood, it is a CrMoV steel with the composition of 4150 and an additive of Vanadium. This drastically increases its impact strength.

Specifications:

MIL-B-11595E

Applications:

gun barrels, rifle barrels. Military, AR15 and M16 rifles. M4 carbine barrels.

Alloy 188 is a cobalt based solid solution-strengthened alloy with high temperature strength and oxidation resistance to 2000F. HA188 has good sulfidation resistance and metallurgical stability. This is a seen by its good ductility after being in high temperature environments.

This material is stronger than nickel based solid solution strengthened alloys, and is much stronger than nickel chromium or iron nickel chromium heat resistant alloys. Due to this, this allows for significant section thickness reduction.

Specifications:

UNS R30188, AMS 5772 (rod, bar, wire), AMS 5608 (plate, sheet, strip), AMS 5801

Common trade names: Haynes 188, Alloy 188.

Applications:

Gas turbine applications ( combustors, flame holders, liners and transition ducts)

Next Generation Metals is able to supply your manufacturing operation metric cold drawn round and hexagon sizes in various grades.

Stainless Steel Grades:

303, 304, 304L, 316, 316L, 430F, ASTM A582, ASTM A276, X8CrNIS 18-9, X2CrNi18-10, X5CrNiMo17-2-2, X6CrNiMoTi17-12, W.Nr 1.4301, DIN# 1.4305, DIN# 1.4306, DIN# 1.4401, DIN# 1.4404, DIN# 1.4571.

Please contact us at 866-364-3904 or sales@ngmetals.com for availability.

C95400 Alumimum Bronze is the common and popular of the aluminum bronze alloys. It is used in many heavy duty applications. This material provides high tensile and yield strength, good ductility, weldability and machinability. C954 has superior resistance to wear, fatigue and deformation with excellent corrosion resistance. C954 exhibits resistance to corrosion in sea water and low oxidation rates at higher temperatures.

Specifications:

UNS C95400, CDA C95400, ASTM B-505/B-505M, ASTM B-271, ASME SB-271, QQ-C-390, QQ-B-671, MIL-B-16033, ASTM B-148, ASTM B-584, ASTM B-763, MIL-C-15345, AMS 4870B, MIL-C-11866

Machine Rating is 60

Applications:

Aerospace, Marine, Chemical. Gears, worm wheels, weld guns, fastener nuts, large screws, clamps, pickling hooks, spur gears, landing gear parts, machine parts, pressure blocks, pump parts, wear plates, bushings, bearings, wear strips, valve bodies, valve seats, valve guides. Widely used in oil and gas industry.

Haynes Alloy 263 is an age hardenable nickel based alloy that has been designed especially to combine excellent aged strength properties with superb fabrication characteristics in the annealed condition. Provided in the solution heat-treated condition it is available in sheet, plate, strip, bar and wire. Strip material is furnished bright annealed.

Waspaloy and some other alloys are stronger at higher temperatures but  it easier to form and weld.

Haynes 263 can be used for applications of up to 1650F.

Specifications:

UNS N07263, AMS 5872E, B50A774A, BS HR10 / AMS 5886

Applications:

Aircraft and land-based turbine engine parts, combustors, transition liners, ring components.

Stainless Grade 440C is a high-carbon chromium steel that was engineered to have stainless properties with maximum hardness. It is used mostly as a bearing steel and in the hardened and tempered condition. 440C can be heat treated but will have about a Rockwell 60 C scale, the hardest stainless steel.

440C has corrosion resistance in normal domestic environments and very mild industrial environments, including many petroleum products and organic materials.

Specifications:

UNS S44004, AISI 440C, AMS 5618, AMS 5630, AMS 6990, ASTM A276, ASTM A314, ASTM A473, ASTM A493, ASTM A690, ASTM A756, QQ-S-763

440C Bearing Quality: AMS 5630, AMS 5880, ASTM A-276, ASTM A-756

Applications:

Bearing assemblies, balls and races. Cutlery, knives, mold inserts, needle valves, ball check valves, aircraft parts, oil well pump parts, valve seats, pump parts, ball studs, nozzles, surgical tools, bushings, wear resistant components.

Bearing Bronze alloy C932 has excellent machining properties, good hardness, strength and wear resistance with excellent anti-friction qualities. C93200 has fair corrosion resistance to seawater and brine. This is suitable for pump and valve components, bearings and bushings with medium loads and speeds with adequate lubrication.

Specifications:

SAE 660 bearing bronze, CDA 93200, ASTM B505, ASTM B-271, ASTM B66. Alloy C93200, ASTM B144-3B, ASTM B-584, , ASTM B-763, QQ-C-390.

Applications:

General utility bearings, bushings, wear plate, valve and pump components, automotive fittings, washers, machine parts, spindle bearings, pump fixtures, insert bearings, pump impellers. Widely used in the gas and oil industry.

Forms:

SOLID BAR . . . . . . . . . . . . . . . . . . ..375” – 16” diameter

HOLLOW BAR (Continuous Cast) . . . .500” I.D. x 1” O.D. thru 14“ I.D. x 16” O.D.

HOLLOW BAR (Centrifugal) . . . . . . . . up to 30” O.D. (stock)

SQUARE BAR . . . . . . . . . . . . . . … . .up to 10” square

WEAR PLATE . . . . . . . . . . . . . . . . . .250” – 10“ thick thru 18” widths

Bar, rod, tube, tubing

Brass 2745 is a lead free alloy  with good machining ability with a rating of 70%.

C27450 is compliant with S3874 and AB1953.

Specifications:

UNS C27450

Applications:

drinking water fixtures and fittings, forged valved and bodies.

M50 VIM-VAR tool steel is very useful in applications for high wear resistance and strength at high temperatures.

Next Generation Metal carries this material in bar form.

Specifications:

• UNS K88165
• UNS T11350
• AMS 6490
• AMS 6491
• ASTM A-600

Applications:

Bearings in aircraft and gas, missile and gas turbines.

4340 alloy steel is a heat treatable and low alloy steel that contains chromium, nickel and molybdenum. It has good shock and impact resistance with good wear and abrasion resistance when hardened. Its toughness and strength improved in the heat treated condition.

This alloy can be quenched and tempered to achieve a wide range of hardness, ductility and strength levels while still being able to resist stress.

In the AMS 6415 cold finished or hot rolled condition, it has hardenability with high strength characteristics. This condition is an optimal choice for highly stressed parts that will be used in severe conditions.

4340 alloy is available in both vacuum milt (VM) and air melt variations.

Specifications:

• AISI 4340
• AMS 6409
• AMS 6415
• AMS 6359
• AMS 6414
• AMS 6454
• ASTM A829
• UNS G43400
• ASTM A29
• ASTM A320
• ASTM A322
• ASTM A331
• ASTM A506
• ASTM A646
• MIL-S-5000

Applications:

Transmission gears and shafts, aircraft landing gear, structural parts such as gears, sprockets, chucks, molds. Crank shafts, valves, crank shafts, mine-drilling parts, gun bodies, connecting rods, axle shafts, impeller shafts, die holders, bolts, flanges, collets, spindles, machine tool arbors.

430F Stainless Steel is a free machining version of 430 Stainless Steel. It has been designed and specifically developed for solenoid core applications in corrosive environments. It cannot be hardened by heat treatment.

Specifications:

UNS S43020, ASTM A-314, ASTM A-473, ASTM A-581, ASTM A-582, ASTM A-838

Applications:

Automatic screw machines, aircraft parts, aircraft gears. Valves, fasteners, surgical equipment, threaded bars, pins, hinges, combustion chamber linings.

430 Stainless Steel is a non-hardenable steel that is known for its good corrosion resistance and formability.

Specifications:

UNS S43000. AISI 430, AMS 5503, AMS 5627, ASTM A-276, ASTM A-182,  ASTM A-268,  ASTM A-314,  ASTM A-473,  ASTM A-479,  ASTM A-493,  ASTM A-511,  ASTM A-554, ASTM A-240, ASTM A-480, ASTM A-666, ASME SA-240, ASME SA-480, ASME SA-666, QQ-S-763

Applications:

Household appliances, vaults, heat exchangers, vending machine components, dishwasher linings, refrigerator cabinet linings, cabinet hardware, element supports and fasteners, automotive trim and lashing wires.

Waspaloy is an age-hardenable superalloy with excellent strength with good corrosion resistance.

Specifications:

• UNS N07001
• AMS 5544
• AMS 5708
• AMS 5828
• AMS 5706
• Capable of AMS 5704
• Capable of AMS 5707

Applications:

• Jet engine turbine parts
• aerospace components
• gas turbines
• springs and fasteners
• Gas turbine blades
• seals
• rings
• shafts.

17-7 Stainless Steel is a precipitation hardened stainless steel that gives high strength and hardness, superb fatigue properties, good corrosion resistance, good formability, and minimum distortion upon heat treatment.

Specifications:

UNS S17700, AISI 631, AMS 5528, AMS 5529, AMS 5568, AMS 5644, AMS 5678, AMS 5824, ASTM A-313, ASTM A-564 Type 631, ASTM A-579, ASTM A-693 Type 631, ASTM A-705, MIL-S-25043, AMS 5673, SAW J217, SAE J467

Applications:

Springs, washers, blades, fluid seal springs, diaphragms, pressings, encapsulated bellows, aerospace applications, oil and petroleum refining equipment, food processing and chemical processing equipment, heat exchangers, power boilers, superheater tubes.

Grade 431 has excellent corrosion resistance, torque strength and high toughness and hardness.

Specifications:

UNS S43100, Grade 431, AMS 5628, ASTM A-276. AMS 5628, ASTM A-314, ASTM A-473,  ASTM A-493, ASTM A-511, ASTM A-579, ASTM A-580, MIL-S-18732, MIL-S-8967

Applications:

Bolt and shaft applications, laboratory equipment, marine systems, beater bars, pump and propellor shafts, nuts and bolts, valve components.

HYMU 80 is a nickel alloy with extremely high and maximum permeability, low coercive force and minimum hysteresis loss, which makes it optimal for magnetic shielding applications.

This material is also known as Permalloy 80 and Moly-Permalloy.

Specifications:

MIL-N-14411C Composition 1, ASTM A-753-78

Applications:

Transformer cores, electro-magnetic shields, high quality motor laminations, stepping motors.

Super Alloy Hiperco 50A alloy is made up of 49% cobalt and 2% vanadium. It has the highest  magnetic saturation of all soft magnetic alloys. This material has high D.C. maximum permeability, low D.C. coercive force and low A.C. core loss.

After heat treating, this alloy keeps it strength making it optimal for applications with high heat and forces, such as rotating parts.

This material is also known as Permendur 2V, Permendur 49.

This material is carried in bar, rod, coil and sheet.

Specifications:

ASTM A-801, MIL-A-47182, MIL-S-1907, MIL-S-1949A, AMS A-47182

Applications:

Material is used mostly for magnetic cores in electrical equipment. In strip form used for aircraft generators and motors. Electromagnets for medical (radiology) applications. Motor laminations, transducers, poles and cores.

Nitronic 40 is a versatile stainless steel that has a high manganese content. This alloy has high strength and excellent corrosion resistance at high temperatures. Yield strength is approximately twice that of Grades 304, 321 and 347.

Specifications:

UNS S21900, UNS S21904, Alloy 219, Alloy 40, XM-10, XM-11, AMS 5656, ASTM A-276, ASTM A-479, ASTM A-314, ASTM A-580, AMS 5595, ASTM A-412, AMS 5561, AMS 5562, XM11, 21-6-9

Applications:

Aircraft components. clamps, flanges, hydraulic tubing, chemical processing, pollution control equipment, cryogenic applications, steam and autoclave parts.

321 Air Melt Stainless Steel is an austenitic steel similar to Grade 304 but with a titanium addition of at least five times the carbon content. This prevents carbide precipitation. This alloy has excellent resistance to oxidation, corrosion with good creep strength.

Grade 321 is not heat treatable.

Specifications:

UNS S32100, ASTM A-240/240M, AMS 5510, AMS 5645, ASME SA-240, ASME SA-312, ASME SA-479, ASTM A-276 Condition A, , ASTM A-276 Condition S, ASTM A-479, QQ-S-763, QQ-S-766D.

Applications:

Aircraft exhaust manifolds, annealing covers, stack lines, boiler casings, jet aircraft components, thermal oxidizers, refinery equipment, high temperature checmical process equipment, welded presser vessels, expansion joints, bellows, furnace parts, heating element tubing, heat exchangers, spiral welded tube for burner pups and flues,

418 Greek Ascoloy is a hardenable martensitic stainless that can achieve deep hardening.

Specifications:

UNS S41800, AISI 615, AMS 5616, AMS 5508, ASTM A-565

Applications:

Gas turbine components, shafts, wheels, engine braces, steam turbine buckets and blades,  compressor blades and parts, high temperature fasteners and bolts.

Stainless Grade 430FR Solenoid Quality is an alloy that has been developed specifically for soft magnetic components that are operated in corrosive environments. It is resistant to corrosion from atmosphere, fresh water, gases, standard beverages, dairy products, etc.

This material is generally stocked with a centerless ground finish.

Specifications:

ASTM A-838 Alloy 2

Applications:

Solenoid valves and injectors.

Nitralloy 135 Modified is a low alloy nitriding steel grade with moderate hardenability. N135 was designed to give high case hardening while keeping its core strength during nitriding.

Nitriding 135MOD comes in either Air Melt or Vac Melt.

VAC-ARC and VIM-VAR melting procedures usually yield the most preferred ingot solidification, as well as superior cleanliness.

Specifications:

• UNS K24065
• AMS 6470
• AMS 6471
• AMS 6472
• AMS 2301
• AMS 2304
• AMS-S-6709
• MIL-S-6709A
• ASTM A-322

Applications:

• Aircraft gears
• shafts
• pinions
• crankshafts
• cams
• camshafts
• bolts.
• gears

Grade 13-8 is a martensitic precipitation hardening stainless steel that has excellent strength, high hardness, superior toughness and good corrosion resistance.

Specifications:

UNS S13800, AISI 632, AMS 5629, AMS 5864, AMS 5840, ASME SA-705, XM-13, XM13, ASTM A-693, ASTM A-564, 13-8Mo, 13-8PH

Applications:

Aerospace such as large airframe structure components, landing gears, shafts, valves, injection molding equipment, petrochemical and nuclear components,

Grade 302HQ is a specialized wire grade used for the manufacture of fasteners.

Specifications:

UNS S30430, ASTM A-493, XM-7, ASTM A-276, ASTM A-493, ASTM F-593

Applications:

Self tapping screws, light machine screws, bolts, set screws, rivets, specialized fasteners, cold heading applications, roofing bolts.

Grade 420 is a high carbon steel with minimum chromium content of 12%. This can be hardened through heat treatment.

This material also comes in a 420 ESR variation.

Specifications:

UNS S42000, X20Cr13, AMS 5506, AMS 5621, ASTM A-276, ASTM A-314, ASTM A-473, ASTM A-580, QQ-S-763, QQ-S-766.

Applications:

shear blades, needle valves, dental and surgical equipment, cutlery,pump shafts, steel balls.

420F Stainless Steel is easy to machine, grind and polish. 420F is a general purpose free machining version of 420 Stainless.

Specifications:

UNS S42020, AISI 420F, AMS 5620, ASTM A-582, QQ-S-764, SAE S1420F, SAW J405

Applications:

Automatic screw machines, cutlery, dental and surgical instruments, hand tools, valve trim, pump shafts, needle valves, ball check valves, gears, cams, pivots,

A2 Tool Steel is an air hardening tool steel that offers good toughness with medium wear resistance with easy machining.

Specifications:

UNS T30102, AISI A2, ASTM A-681, SAE J437, SAE J438

Applications:

Blanking, coining, forming, trim and punching dies, drill bushings, gauges, lamination dies. Long Punches, rolls, master hubs, precision tools, shear blades and slitters.

A2 Drill Rod

S7 tool steel is good for general tooling and molding applications. S7 has good toughness and shock resistance.

Specifications:

UNS T41907, ASTM A-681, QQ-T-570, ASTM A-597

Applications:

Shear blades, chisels, swaging and gripper dies, punches, plastic injection molds,

AISI O-1 Hardened Tool Steel that is oil quenched in heat treatment.

Specifications:

UNS T31501, AISI O1, ASTM A+681, QQ-T-570, SAE J437, SAE J438

Applications:

Tools for cuttings, blanking, punching, piercing, cropping, shearing, trimming. Gauges, screw dies, precision tools, reamer, form cutters, measuring tools, drills, taps, nozzles.

O1 Drill Rod

W-1 Tool Steel is the most commonly available water-hardening tool steel grade and can be easily hardened.

Specification:

UNS T72301, ASTM A-686, SAE J437, SAE J438

Applications:

Cold heading, metal cutting tools,

Invar 36 is a low expansion alloy with 36% nickel that maintains its structure at out of normal atmospheric temperatures.

Specifications:

• UNS K93600
• UNS K93601
• UNS K93603
• UNS K93050
• ASTM F-1684
• ASTM B-753
• MIL-S-16598
• MIL-I-230IIC
• ASTM B388
• ASTM B753
• Boeing D-33078

Applications:

• Cryogenic component
• Precision scientific instruments
• optoelectronic devices
• optical and laser benches,
• motor valves
• physics laboratory devices
• precision condenser plates
• watch parts
• clock pendlems.

NILO 36, Pernifer 36, Super Invar.

A6 is a air-hardening tool steel that exhibits good toughness and superb dimensional stability.

Specifications:

UNS T30106, ASTM A6, ASTM A-681, QQ-T-570

Applications:

Blanking, mandrels, forming dies, chuck jaws, feed fingers, precision tools, spindles, heavy duty punches, coining dies, dowel pins, shear knives, gages.

Next Generation Metals, Inc. can supply the following magnesium items:

Specifications:

UNS M11100: AZ10A

UNS M11311: AZ31, AZ31B

UNS M11312: AZ31C

UNS M11610: AZ60A, AZ61A

UNS M11630: AZ63A

UNS M16600: ZK60, ZK60A

UNS M11800: AZ80, AZ80A, AZ81A

UNS M18430: AZ61, Elektron 43

Applications:

aerospace, defense ( missiles ), and satellite industry.

S1 tool steel is a shock-resisting steel.  It performs excellently in cold and hot work shock applications.

Specifications:

UNS T41901, AISI S1, ASTM A681, QQ-T-570, ASTM S1, SAE J438

Applications:

Master hobs. piercers, forming tools, hand chisels, pneumatic tools, shear blades, mandrels, machine parts.

S5 is a tool steel with high toughness and is able to hardened to Rc 62. It has the highest impact toughness of the S type steels.

Specifications:

UNS T41905, AISI S5, ASTM A681, QQ-T-570, SAE J437, SAE J438, ASTM S5

Applications:AISI S

hand chisels, pneumatic tools, hammers, stamps, brake dies, shear blade, drift pins, slitters, collets

Next Generation Metals supplies precision machine and swiss straightener shops with machining bar with absolute dimensional consistency.

Our AccRound Sales Staff is a one-stop raw material and grinding source that can lower your cost and lead time.

Next Generation Metals AccuRound precision ground bar can be counted on for consistent diameter tolerance, roundness and straightness.

We source material from the highest quality mills and our grinding will give you superior straightness and tolerance throughout the length of your bar. We can hold tolerances of +/-.0001 on any 12′ length bar with +/-.00005 roundness.

We supply domestic and foreign material from Europe. We stock DFARS material as well. We stock oversizes for our customers with uncommon requirements.

We also can supply you with heat treating, straightening, bar end chamfering and saw cutting.

Next Generation Metals supplies precision machine and swiss straightener shops with machining bar with absolute dimensional consistency.

Our AccRound Sales Staff is a one-stop raw material and grinding source that can lower your cost and lead time.

Next Generation Metals AccuRound precision ground bar can be counted on for consistent diameter tolerance, roundness and straightness.

We source material from the highest quality mills and our grinding will give you superior straightness and tolerance throughout the length of your bar. We can hold tolerances of +/-.0001 on any 12′ length bar with +/-.00005 roundness.

We supply domestic and foreign material from Europe. We stock DFARS material as well. We stock oversizes for our customers with uncommon requirements.

We also can supply you with heat treating, straightening, bar end chamfering and saw cutting.

Next Generation Metals supplies precision machine and swiss straightener shops with machining bar with absolute dimensional consistency.

Our AccRound Sales Staff is a one-stop raw material and grinding source that can lower your cost and lead time.

Next Generation Metals AccuRound precision ground bar can be counted on for consistent diameter tolerance, roundness and straightness.

We source material from the highest quality mills and our grinding will give you superior straightness and tolerance throughout the length of your bar. We can hold tolerances of +/-.0001 on any 12′ length bar with +/-.00005 roundness.

We supply domestic and foreign material from Europe. We stock DFARS material as well. We stock oversizes for our customers with uncommon requirements.

We also can supply you with heat treating, straightening, bar end chamfering and saw cutting.

A9 Tool Steel is an air-hardening cold work steel that allows minimal cracking and distortion on quenching.

Specifications:

UNS T30109, ASTM A681, QQ-T-570, AISI A9, ASTM A9

Applications:

Blanking and forming dies, shear blades, hot gripper dies, drill bushings, knurling tools, master dies and gauges.

15-7 Stainless Steel is a semi-austenitic precipitation hardening stainless steel with high strength and good corrosion resistance.

This material is able to be heat treated to Condition TH1050, Condition RH950, Condition, Condition CH 900.

Specifications:

UNS S15700, AMS 5520, AMS 5657, AMS 5812, AMS 5813, ASTM A564, ASTM A579, ASTM A693, ASTM A705, MIL-S-8955

Applications:

Retaining rings, springs, aircraft bulkheads.

440A Grade has a a slightly lower percentage of carbon than other 440 grades. This material is not readily available like 440C.

Specifications:

UNS S44002, ASTM A276, ASTM A314, ASTM A473, ASTM A580, ASTM f899, QQ-S-763

Applications:

valve components, ball bearings, chisels, surgical equipment, knife blades, valve seats.

Grade 302 has a slightly higher carbon content than grade 304. This is mostly made in strip and wire forms.

Specifications:

UNS S30200, AMS 5515, AISI 302, AMS 5516, AMS 5636, AMS 5637, AMS 5688, ASME SA240, ASTM A167, ASTM A240, ASTM A276, ASTM A313, ASTM 314, ASTM A473, ASTM A478, ASTM A479, ASTM A554, ASTM A666, QQ-S-763, QQ-S-766, QQ-W-423, MIL-S-862, AMS 5788

Applications:

form springs, washers, screens, cables, pressure vessels, car and radar antennas, bottling machinery, home appliances, jewelry, retainers, sanitary and cryogenic applications.

4140 Gun Barrel Steel is a chromium molybdenum alloy steel with good hardness penetration. This material was designed with consistent hardness and high strength.

Specifications:

AISI 4140,

Applications:

Gun Barrels

Speak to Next Generation Metals about 4140 Chrome Moly Gun Barrel Steel.

O-1 Drill Rod Tool Steel is an electric furnace melt oil-hardening steel with a fully spheroidized body. It is non-shrinking with excellent abrasion resistance, toughness and machinability characteristics. This is the most widely used grade of drill rod.

Standard bar lengths are 3 foot long but can be supplied in 12 foot long as well.

This material is stocked in the annealed condition and ground and polished in tight tolerances.

Specifications:

UNS 20102105, SAW J437, ASTM A681

A-2 Drill Rod Tool Steel is used instead of O-2  when you require improved wear resistance, safer hardening, and less distortion is required. A-2 drill rod is a fine grain, electric furnace air-hardening chrome tool steel.

Standard bar lengths are 3 foot long but can be supplied in 12 foot long as well.

This material is stocked in the annealed condition and ground and polished in tight tolerances.

Specifications:

UNS 20102105, SAW J437, ASTM A681

D-2 Drill Rod Tool Steel is an air-hardening steel that is known for its maximum wear resistance abilities. That and its high compressive strength make it perfect for long production runs. It is also an outstanding choice when high production and/or close tolerances are needed on finished parts. It is ideally used for tools and dies.

Standard bar lengths are 3 foot long but can be supplied in 12 foot long as well.

This material is stocked in the annealed condition and ground and polished in tight tolerances.

W-1 Drill Rod Tool Steel is a popular, versatile and inexpensive grade of drill rod tool steel. It has a high carbon content so it is usually used without heat treat. Its tool life isn’t equal to O-1 tool steel.

Standard bar lengths are 3 foot long but can be supplied in 12 foot long as well.

This material is stocked in the annealed condition and ground and polished in tight tolerances.

Specifications:

UNS 20102105, SAE J437, ASTM A686

H-13 Drill Rod Tool Steel is a free machining grade that is prehardened to Rc 42-46 and is designed for hot work applications. Since it has made in the prehardened condition, size change during heat treatment phase are eliminating and you can machine to finish dimensions. VIS-44 (H-13) is ideal for high-strength machinery parts.

Standard bar lengths are 3 foot long but can be supplied in 12 foot long as well.

This material is stocked in the annealed condition and ground and polished in tight tolerances.

S-7 Drill Rod Tool Steel is an air or oil hardening die steel with toughness and wear resistance properties that is used for many tooling applications. It is an excellent shock steel where tool temperatures do not exceed 1000F.

S-7 is used for cold work tools (shear blades, gripper dies, chisels and punches).

Standard bar lengths are 3 foot long but can be supplied in 12 foot long as well.

This material is stocked in the annealed condition and ground and polished in tight tolerances.

M-2 Drill Rod Tool Steel is a tungsten-molybdenum high speed tool steel that is hardenable to Rc 65. It has excellent abrasion resistance with good toughness. It has superior resistance to softening at elevated temperatures.

Standard bar lengths are 3 foot long but can be supplied in 12 foot long as well.

This material is stocked in the annealed condition and ground and polished in tight tolerances.

Specifications:

UNS 20102105, SAW J438B, ASTM A600

C952 Alumimum Bronze is a bronze alloy with excellent conditions for corrosion resistance, wear and impact.

This material can be heat treated.

Specifications:

UNS 95200, CDA C95200, SAE 68A, ASTM B505/B505, ASTM B271, ASME SB-271,  ASTM B-148, ASTM B-584, ASTM B16

Applications:

Electrical hardware, fasteners, marine hardware, slides, bolts, hydraulic valve parts, propellers and marine engines. Large gear parts, hydrant parts, valve seats, welding jaws, valve bodies, wear plates, bearing liners, pump parts, valves, pump rods, gears, plungers,

C17200 beryllium copper is available in both solution and precipitated heat treated in bar and tube. When this material is age hardened, it has the highest strength and hardness of all the commercial copper alloys.

This material is also known as Alloy 25 or CDA 172.

Specifications:

UNS C17200, AMS 4725, AMS 4650, AMS 4651, MIL-C-21657, SAE J461, AMS 4650, AMS 4535, ASTM B194, ASTM B643, ASTM B196, ASTM B194, AMS 4533, ASTM B570, RWMA Class 4

Applications:

Bearings, aircraft landing gear, bushings, washers, screws, bolts, pumps, springs, shafts, valves, bourdon tubes, roll pins, firing pins, precision screw machine parts, corrosion resistant components.

C955 is a high strength nickel aluminum bronze with high hardness that is suitable for heavy duty, high shock and high impact components and applications. C955 has great corrosion resistance, heat resistance, good weldability and machinability.

Specifications:

UNS 95500, ASTM B-505M, AMS 4880, ASTM B-271, QQ-C-390, MIL-B-16033, C95500, SAE J461, SAE J462.

See C95520 for AMS 4881.

Applications:

Bearings, bushings, landing gear bearings, valve guides, corrosion resistant parts, piston guides, gears, wear parts, pump parts, machine tool parts, aircraft and military parts and applications. marine propeller hubs, marine hardware, marine shafts, marine sleeves, valves seats, valve components, government fittings.

C630 is a high strength nickel aluminum bronze that exhibits great abilities in abrasive wear resistance, friction, and corrosion resistance.

Specifications:

UNS C63000, AMS 4640, QQ-C-465B, ASTM B-150,  ASME SB150, ASTM B-124, ASTM B-283, CDA 63000, SAE J461, SAE J463

Applications:

Aircraft landing gear, strut bearings, main pistons, hydraulic bushings, heat exchanger flanges and headers, tanks, valve balls, pump shafts, balls, gears, pump parts, valve seats, bolt, nuts, propellers.

C95900 aluminum, bronze is known for its high strength and excellent corrosion resistance. This material is a heavy duty bearing alloy with good wear resistance and great impact resistance.

Specifications:

UNS C95900, ASTM B505/B505M, CDA 959, ASTM B148

Applications:

Gears, valve guides, velve seats, inserts, dies,

A-10 is an air hardened tool steel has great metal-to-metal resistance to wear and galling. A-10 also has great toughness and excellent machinability.

Specifications:

UNS T30110, ASTM A681, QQ-T-570, ASTM A10,

Applications:

Cams, thread gages, sleeves, meat granulator places, shear blades, punches, bar feed guides, forming rolls, bushings, sleeves,

This material is available as sheet, plate and bar.

O-6  is an oil hardening Cold-work tool steel with great metal-to-metal resistance to wear and galling. O-6 also has great toughness and non-seizing characteristics.

Specifications:

UNS T31506, ASTM A681, QQ-T-570, SAE J437, SAE J438, AISI O6.

Applications:

Forming dies, piercing dies, blanking dies, forming rolls, punches, bushings, gauges, wear plates.

This material is available as sheet, plate and bar.

A-8 tool steel is an air-hardening cold work tool and die steel that has excellent toughness.

Specifications:

UNS T30108, AISI A8, ASTM A681, QQ-T-570

Applications:

Punches, drift pins, pneumatic tools, chuck jaws, hammers.

L6 Tool Steel is an oil hardening tool steel with good hardness, toughness and wear resistance.

Specifications:

UNS T61206, ASTM A681, SAE J437, AISI L6

Applications:

Punches, dies, cold forming tools.

M4 is a high speed tool steel specifically designed for better wear resistance than M2 or M3.

Specifications:

UNS T11304, ASTM A600, SAE J437, SAE J438, QQ-T-590, CPM M4,

Applications:

Punches, die inserts, cutting tools

Data is typical and should not be construed as actual values for any catagory. Applications and technical information require engineers and tool designers to exercise independent judgement

Alloy 263 is a precipitation hardenable alloy that is designed to combine good aged strength with great fabrication characteristics in the annealed condition. This material is provided in the solution treated condition. This alloy gives high strength, corrosion resistance, great formability, ductility and weldability.

This material is supplied as rod, bar, wire, sheet, strip, and plate.

Specifications:

UNS N07263, AMS 5872, AMS 5966, GE B50A774, GE B50A783,

Also known as Cobalt 263, Nimonic Alloy 263, Haynes 263

Applications:

Gas turbines rings, casings, liners, combusters, aircraft turbine engines, transition liners, ring components,

Super alloy MP 159 has a unique combination of ultra high strength, high ductility and corrosion resistance. This alloy can achieve a tensile strength of over 265KSI.

Specifications:

UNS R30159, AMS 5841, AMS 5842, AMS 5843

Applications:

Gas turbine components, fasteners, jet engine components, drive components, prosthetic devices, marine and petroleum applications.

330 Stainless has great resistance to oxidation and carburization up to 2200F with high strength.

Next Generation Metals carried Alloy 330 Annealed Stainless Steel in round bar, flat bar, plate and sheet.

Specifications:

UNS N08330, AISI 330, AMS 5592, AMS 5716 (bar), ASME SB511 (bar), ASME SB535, ASME SB536 (sheet and plate), ASME SB710, ASTM B512

Applications:

Muffles, retorts, baskets, radiant tubes, heat exchangers, heat treating equipment, chemical and petrochemical processing, power generation, thermal processing, ore processing, gas turbine components.

Grade 310 Stainless is designed for high temperature service due to its high temperature properties and good ductility and weldability. This material has good resistance to oxidation, sulfidation and carburization.

Grade 310S (UNS S31008) is has a lower carbon content and reduces its strength at high temperatures.

Next Generation Metals carried Alloy 310 and 310S Annealed Stainless Steel in round bar, flat bar, plate and sheet.

Specifications:

UNS S31000, AISI 310, AMS 5651 (bar), ASTM A276 (bar), QQ-S-763, ASME SA-479, ASTM A240 (plate, sheet, strip), AMS 5521, ASME SA-240, ASME SA-312, ASTM A312

Applications:

Furnace parts, conveyor belts, rollers, auto exhaust parts, oil burner parts, heat treatment baskets, heat exchangers, refractory anchor bolts, muffles, annealing covers, cryogenic structures.

Stainless Grade 309 and 309S has high corrosion resistance and strength compared to other 300 series stainless.

Next Generation Metals carries 309 Stainless Steel in round bar, pipe, plate and sheet.

Specifications:

UNS S30900, UNS S30908 (sheet, strip and plate), UNS S30909 (309S), AISI 309, AMS 5523, ASME SA240, ASME SA312, ASME SA479, ASTM A240, ASTM A276 Condition S, ASTM A312, ASTM A479, QQ-S-763, QQ-S-766

AMS 5592, AMS 5716 (bar), ASME SB511 (bar), ASME SB535, ASME SB536 (sheet and plate), ASME SB710, ASTM B512

Applications:

Annealing covers, waste incinerators, muffles, furnace fans, thermowells, anchor bolts, aircraft and jet engine parts, refinery and chemical processing equipment.

C63020 is a nickel aluminum bronze that is used for parts where extra high strength and hardness with some ductility and toughness. These characteristics provide extreme wear resistance for abrasive wear, extreme loads and high impact landings.

This material is provided in solution treated and tempered bar.

Specifications:

UNS C63020, AMS 4590, ASTM B-150, ASTM B-315

Applications:

Wellhead components, rock bit bearings, landing gear parts, forming roll bearings, marine pump parts and bushings, valve parts, bearings, valve balls, cryogenics, tank track bearings, aircraft components, military aircraft bushings,

Kovar is a vacuum melted alloy with a narrowly defined chemical composition.

Next Generation Metals stocks Kovar in sheet, plate, rod, bar, coil and strip.

Specifications:

UNS K94610, ASTM F-15, MIL-I-23011 Class 1,

Applications:

Power tubes, hermetic seals, microwave tubes, transistors and diodes.

Next Generation Metals carries this in tube, sheet, plate, strip and wire.

Also known as Pernifer 40

Specifications:

• UNS K94100
• UNS K94200
• ASTM F30
• ASTM B753
• MIL-I-23011 Class 5

Applications:

• Used for semiconductor lead frames in circuits
• thermostat rods
• glass-to-metal seals
• sealing glass envelopes of electric bulbs
• radio valves
• automotive and industrial lamps
• television tubes
• fluorescent lights.
• Transformer and capacitor bushings
• Electronic tubes

410 Air Melt Stainless is a general purpose martensitic stainless steel which provide good corrosion resistance properties. This material can increase its corrosion resistance by hardening, tempering and polishing.

410 Stainless Steel is resistant to hot gases, steam, food, mild acids and alkalies, fresh water and dry air.

Next Generation Metals stock this in pipe, plate, sheet, round bar, square bar and flat bar.

Specifications:

UNS S41000, AISI 410, ASTM A-176, ASTM A-182, ASTM A-193, ASTM A-194, ASTM A-240, ASTM A-276, ASTM A-314, ASTM A-473, ASTM A-479, ASTM A-511, AMS 5504, AMS 5505, AMS 5591, AMS 5613, AMS 5776, QQ-S-763, QQ-S-766, MIL-S-862, SAE J405, SAE J412.

Applications:

Cutlery, fasteners, bolts, screws, bushings, nuts, shafts, pumps, valve components, gas and steam turbine components, press plates, gate valves.

Grade 416 is a free-machining stainless steel with machinability that can be improved by adding sulphur. This reduces formability, weldability and corrosion resistance.

Next Generation Metals carries 416 Annealed, Heat Treated Condition T (intermediate temper), Heat Treated Condition H (hard temper),

We carry this in wire, plate, sheet, tube and coil. Also round bar, flat bar and hexagon.

Specifications:

UNS S41600, AISI 416, AMS 5610, ASTM A-194, ASTM A-581, ASTM A-473, ASTM A-582, ASTM A-314, QQ-S-763, QQ-S-764, ASME SA-194, ASTM A-194, MIL-S-862, SAE J405, SAE 514165, MIL-W-52263

Applications:

Valves, pump shafts, gold club heads, rivets, axles, aircraft fittings, fire extinguisher inserts, motor shafts, gears, bolts, nuts, pistons, bolts, automatic screw machine components, electric motors, axles, bolts, fasteners, studs, cutlery, steam and gas turbines.

440F SE is a free machining high carbon chromium stainless steel that contains selenium and has high hardness, non-galling and non-seizing properties. This material is heat treatable.

Specifications:

UNS S44023, AMS 5632 Type 2, ASTM A-582, ASTM A-484

Custom 465 Stainless is a martensitic heat treatable alloy capable of 250,000+ PSI tensile in the H950 condition.

This material is double vacuum melted, martensitic age-hardened alloy that has a combination of strength, toughness and corrosion resistance.  The tensile strength can be as high as 255 ksi, with a fracture toughness of about 80-90 ksi with a similiar corrosion resistance of 304 stainless.

Vacuum arc remelt (VAR) furnaces are used to produce Custom 465 stainless steel.

Specifications:

• UNS S46500
• AMS 5936 Capable of H1000
• ASTM A-564 Capable of H1000
• ASTM F-899
• BMS-7-364

Applications:

Landing gear components, sporting equipment, slat components, pneumatic cylinders, braces, struts, engine valves springs, torsion bars, oil and natural gas, endoscopic instruments, scrapers, cutters, suture needles, drive shafts, gold club faceplates, firearm cylinders, speed boat propellers.

Super Alloy Nickel 205 is one of the essentially pure nickel material. Titanium and aluminum is added to increase its electrical and mechanical properties. 205 has great corrosion resistant properties.

Next Generation Metals are produced in sheet, strip and wire.

Specifications:

UNS N02205, AMS 5555, ASTM F1, ASTM F3, MIL-N-46025

Applications:

Mechanical supports, terminals, support wires, vacuum tube components, pins, electrical and electronic components,

Copper C10100 is 99.99% pure copper and has high conductivity. This material is used primary in the electric and electronics industry.

Next Generation Metals carried this material in bar, plate and sheet.

Specifications:

• UNS C10100
• CDA 101
• AMS 4700
• ASTM B1
• ASTM B111
• ASTM B133
• ASTM B152
• ASTM B172
• ASTM B173
• ASTM B174
• ASTM B187
• ASTM B188
• ASTM B189
• ASTM B2
• ASTM B224
• ASTM B246
• ASTM B272
• ASTM B298
• ASTM B3
• ASTM B33
• ASTM B355
• ASTM B359
• ASTM B432
• ASTM B447
• ASTM B451
• ASTM B470
• ASTM B48
• ASTM B49
• ASTM B496
• ASTM B640
• ASTM B641
• ASTM B698
• ASTM B75
• ASTM F68
• MIL-B-18907
• MIL-W-3318
• MIL-W-85
• QQ-B-575
• QQ-B-650
• QQ-W-343

Applications:

• Automotive rectifiers
• bus conductors
• power substations
• coaxial cable
• coaxial tube
• vacuum seals
• seals
• cryogenic shunts,

C145 tellurium copper has high conductivity and corrosion resistance. This is a strong free machining copper alloy due to the addition of tellurium.

C145 has a machinability rating of 85% compared to pure copper of 20%

Next Generation Metals carried this in various forms of bar.

Specifications:

UNS C14500, ASTM B301, ASTM B124, CDA 145.

Applications:

Electrical applications, Gas cutting nozzles, automatic screw machine parts, electrical switches, welding torch tips, fasteners,

C17300 beryllium copper is heat treatable, ductile and can be hardened. C173 has the same mechanical and physical properties of C17200.

Next Generation Metals is available in rod, wire, plate, sheet, strip, tube, and pipe.

Specifications:

UNS C17300, ASTM B-196, ASTM B-197. Alloy M25.

Applications:

Electric switches, electric connections, relay blades, electric motor components, fasteners, pump parts, bearings, precision screw machined parts, corrosion resistant molds, washers, screws, bolts, retaining rings, lock washers, spline shafts, valves, rolling mill parts, pumps, shafts, diaphragms bourdon tubing.

C17500 and C17510 has high electrical and thermal conductivity with good strength. Both C17500 and C17510 have identical properties and characteristics.

Next Generation Metals has this available in round bar, rectangles, square, plate and tube.

Specifications:

UNS C17500, Alloy 10, ASTM B-441, ASTM B-534, MIL-C-81021, SAE J461, SAE J463. RWMA Class 3

Applications:

Bearings, fasteners, fuse clips, welding electrodes, springs, precision screw machined parts, electrical and electronic connectors, corrosion resistant components.

C46400 is a type of brass-copper alloy known as naval brass. C46400 is known for its resistance to wear, fatigue, galling and stress corrosion cracking, hot workability and hot forgeability.

Next Generation Metals has this material available in rod, bars, tubing, strip, plate, and sheet.

Specifications:

UNS C46400, AMS 4611, ASTM B-21, CDA 464, ASTM A-171, ASME SB-171, ASTM B-124, ASTM B-283, ASTM B-171, ASTM B-432, ASTM F-467, ASTM F-468, MIL-W-6712, QQ-S-639, SAE J461, SAE J463

Applications:

C464 is used in Marine hardware, wearplates, bushings, cannons, lock pins, fasteners, rivets, bolts, nuts, valve stems, balls, heat exchanger tube, aircraft turn buckle barrels, bearing dies, propeller shafts, marine hardware, pressure bearings, shafting, propeller shafts, missile components, fittings, condenser plates, welding rod,

C51000 Phosphor Bronze has a higher yield strength than other readily available cast products. Adding in phosphor to this bronze alloy increases its wear resistance, fatigue resistance and hardness.

Tempers available are H04, Hard, H08 Spring.

Specifications:

ASTM B-139, QQ-B-750, CDA 51000, ASTM B-139, ASTM B-159, SAE J461, SAE J463, AMS 4625, MIL-B-13501, MIL-W-6712, QQ-W-321, ASTM F-467, ASTM F-468

Applications:

Resistance wire, bearings, bushings, gears, shafts, pinions, thrust washers, valve parts, wire brushes, fuse clips, lock washers, cotter pins, chemical hardware, springs, sleeve bushings, bourdon tubes, beater bar, welding rods, bridge bearing plates, fasteners, electronic and precision instrument parts, springs and gears.

ASTM F1058 is a cobalt chrome based alloy that is made fir surgical implants, springs and other applications. This alloy was originally developed for making watch springs. ASTM F-1058 has excellent corrosion resistance, mechanical strength and fatigue resistance.

Specifications:

UNS E30003, UNS R30008, AISI 1058, ASTM F-1058, AMS 5833, AMS 5834, AMS 5875, AMS 5876, NACE MR0175

Equivalent to Phynox, Elgiloy, Conichrome,

Applications:

Surgical implants such as stents, pacemaker led conductors, surgical clips, orthopedic cables and orthodontic appliances, precision spring material for watchmaking industry.

ASTM F-1058 is a cobalt chrome based Superalloy that is made for medical and surgical devices and implants. It has high fatigue strength, wear resistance and corrosion resistance.

Specifications:

UNS R31537, UNS R31538, ASTM F-1537, ASTM F-799.

Equivalent to Nickelvac

Applications:

Surgical implants such as stents, pacemaker led conductors, surgical clips, total joint replacement.

M42 is a super high speed molybdenum steel designed for high hardness and superior hot hardness. This tool steel is an great choice for machining high strength, pre-hardened and high hardness alloys material used for the aerospace, oil and power generation industries. M42 has good wear resistance.

Also known as CPM REX M42, REM M42.

Specifications:

UNS T11342, ASTM A-600, QQ-T-590

Applications:

Used for twist drills, taps, cutters, reamers, broaches, saws, knives.

Grade 305 stainless was designed for great formability, good strength and excellent corrosion resistance. Grade 305 has low work and strain hardening rates. This material is not magnetic and cannot be hardened by heat treatment.

Next Generation Metals can supply this to you in bar, wire, sheet, coil and strip.

Specifications:

UNS S30500, ASTM A-240 for annealed condition, AMS 5514, AMS 5685, ASTM A-276, ASTM A-314, ASTM A-493, QQ-S-763, ASTM A-666 for tempered material.

Applications:

Barrels, shells, cold headed rivets, cold headed screws, spun or deep drawn eyelets, automatic screw machines, electronic enclosure applications, drawn housings, tank covers, writing instruments, kitchen utensils, dairy industry, steam traps, appliances,

Grade 347 stainless is resistant to intergranular corrosion.

Next Generation Metals can supply this in plate, round bar, coil and sheet.

Specifications:

UNS S34700, UNS S34709, AMS 5512, AMS 5646, AMS 5680, ASME SA-240, ASTM A-193, ASTM A-240, ASTM A-269, ASTM A-479, ASTM A-262, QQ-S-763

Applications:

Oil refineries, hanger rods, fired heat tubes, power generation industry, high temperature gaskets, expansion joints, rocket engine parts, chemical production equipment.

Alloy 350 stainless steel has good high temperature strength and corrosion resistance in ordinary conditions. Also known as Type AM 350 is a heat treatable.

Next Generation Metals can supply this material in bar, strip and wire,

Specifications:

UNS S35000, AISI 633, AMS 5546, AMS 5548, AMS 5554, AMS 5745, AMS 5774, AMS 5775, ASTM A-579, ASTM A-693, MIL-S-8840, Type 633, SAE J467,

Applications:

Gas turbine compressor components, blades, discs, rotors, shafts, bellows, industrial cutters, knives, valve components,

AM-355 is a heat treatable alloy brings that is corrosion resistance. AM 355 is similar to AM 350.

AM-355 is also known as Alloy 355.

Specifications:

UNS S35500, AISI 634, AMS 5547, AMS 5549, AMS 5743, AMS 5744, ASTM A-564, ASTM A-579, ASTM A-593, ASTM A-705, MIL-S-8840

Applications:

Industrial cutters, knifes, vale and gas turbine components, blades, discs, shafts.

Next Generation Metals is able to supply this in bar, plate, sheet and strip.

Specifications:

UNS N06333, AMS 5593, AMS 5717, ASTM B-718, ASTM B-719, ASTM B-722, ASTM B-723, ASTM B-726

Applications:

Refineries and coal applications, heat treating muffles, shafts.

Armor Steel in quenched and tempered armored heat treated steel plate.

MIL-A-23560 heat treated plate made for good ballistic resistance.

MIL-DTL-46177 heat treated plate has higher hardness than MIL-A-12560 with thickness up to .250″ thick.

MIL-DTL-46100 heat treated plate provides excellent resistance to penetration with thickness up to 2″ thick.

AR500/AR500F is a premium quenched and tempered plate through hardened war resistant grades of abrasive resistant steel used for military and ballistic purposes. AR500F has can resist more impact than AR500. Typical hardness is BHN 460-544 and is used in mining equipment, the trailer and construction industry.

Next Generation Metals can supply this in plate from .1875 to 2″ thick.

C86300 Manganese Bronze is a high strength, non-treatable copper needed for outstanding wear characteristics and high bearing strength.

Next Generation Metals can supply this in bar and plate.

Specifications:

CDA 86300, ASTM B22, ASTM B-505, SAE 430B, SAE J461, SAE J462, QQ-C-390, MIL-C-22229

Applications:

Brackets, electrical components, screw down nits, marine hardware, clamps, boat parts, heavy duty load bearing, large valve stems, gears, hydraulic cylinder parts, screw down nuts,

Hastelloy N is a nickel based alloy with high molybdenum content designed for hot oxidation resistance to fluoride salts.

Next Generation Metals supplies this in tube, plate, bar and solution annealed sheet. Also known as Nickel Alloy X.

Specifications:

N10003, AMS 5607, AMS 5771, ASTM B366, ASYM B434, ASTM B573, MIL-N-24390B

Super Alloy N155 has good oxidation resistance at high temperatures and good corrosion resistance to sulfuric acid and nitric acid.

Specifications:

UNS R301555, AMS 5532 (sheet, plate), AMS 5768, AMS 5769, AISI 661, AMS 5585, AMS 5794, ASTM B-639, GE B50A484

Applications:

High temperature bolts, aircraft tail pipes, aircraft exhaust manifolds, nozzles, airplane turbine combustion chamber and afterburner components, turbine blades, industrial furnace parts and fittings,

Rene 41 is a age hardening superalloy with great strength. Rene 41 has been designed for use in highly stressed high temperature components. It is highly corrosion and oxidation resistant.

Next Generation Metals carries this in bar, sheet and plate.

Specifications:

UNS N07041, AISI 683, AMS 5545, AMS 5712, AMS 5713, AMS 5800, Capable of AMS 5713.

Applications:

Jet engine components, missile components, high speed airframe components, turbine casings, wheels, fasteners, bolting, springs, after burner parts, marine applications.

Next Generation Metals can supply Grade 304VM in rod and wire.

Specifications:

S30403, ASTM A-2746, AMS 5647

Applications:

Surgical and dental instrumentation.

These are three grades of fusion-welded pressure vessel steel that comes in sheet and plate, which vary in their yield and tensile strengths.

Specifications:

ASTM SA 285 Grade A

ASTM SA 285 Grade B

ASTM SA 285 Grade C, UNS K02801

Next Generation Metals can supply this in up to 2″ thickness.

Applications:

Tanks, pressure vessels,

Low expansion 45 alloy has a constant rate of thermal expansion to about 538C and is used mostly in the telecommunications industry.

Alloy 45 is available from Next Generation Metals in coil, sheet and plate.

Applications:

Thermostats, telecommunication.

Super alloy 46 is a expansion controlled alloy with 46% Nickel.

Next Generation Metals has this available in sheet, strip and plate.

Specifications:

UNS K94600, ASTM F-30, MIL-1-23011 CL 4

Applications:

Metal and glass seals for hermetic and electronic tubes, jet aircraft compressor blades and rotor discs,

Alloy 52 has thermal expansion characteristics.

Next Generation Metals has this available as rod, bar, plate, strip and coil.

Also known as Pernifer 50, NILO 50, Glass Seal 52.

Specifications:

UNS N14052,  UNS K94100, ASTM F-30, MIL 1-23011 Class 2

Applications:

Used in mercury-wetted reed switches, metal seals for electronic tubes, automotive and industrial lamps, specialty hermetic devices.

Alloy 48 is a controlled expansion alloy with nickel content is 48%.

Next Generation Metals has this available as rod, bar, strip and coil.

Also known as Pernifer 48, NILO 48, Glass Seal 48.

Specifications:

UNS K94800, ASTM F-30, MIL 1-23011 Class 3

Applications:

Metal seals for electronic tubes, automotive and industrial lamps, specialty hermetic devices.

Commercially pure wrought nickel with lower carbon than Nickel 200. Nickel 201 has good resistance to corrosion in acids and to caustic alkalis and neutral salt. This material provides highly ductile mechanical properties.

Nickel 201 is not hardenable by heat treatment.

Next Generation Metals can supply this to you in strip, wire, rod, bar and plate.

Specifications:

UNS N02201, ASTM B-160, ASTM B-162, ASTM A-480, ASTM B-564, ASTM B-16, ASME SB-160, ASME SB-564, ASME SB-162, ASME SB-161

Applications:

Production of viscose rayon, manufacture of vinyl chloride monomer, reactors and vessels,

A commercially pure wrought nickel alloy with excellent corrosion resistance with high electrical and thermal conductivities.

Specifications:

UNS N02233, ASTM F-1, ASTM F-3, ASTM F-4

Applications:

Next Generation Metals provides its clients with custom sizes of Pump Shaft Quality material in various grades of stainless steel. PSQ is a process where the material is turned, ground and polished material used mostly in the rotating industries.

The tight diametrical tolerance accomplished through grinding improves the wear and gives the manufacturer a highly consistent product. We also straighten the material for minimal vibration through the length of the shaft.

We can supply PSQ in custom sizes and with finishes up to 8 RMS to offer our customers a superior precision product based on their specifications.

Please call us or email for our current pricing on pump shaft quality stainless.

316 PSQ Stainless

410 PSQ Stainless

416 PSQ Stainless

17-4PH PSQ Stainless

XM-19 (Nitronic 50 PSQ

K500 PSQ

Applications:

Rotary Shafts, Rotary Valves, Valve Shafts, Cylinder Shafts, Boat Shafts,

Next Generation Metals stocks many sizes of Stainless Steel flat bar sizes. Our processes are saw cutting and we also provide shearing up to .500″ and plasma cutting up to 3″.

Alloy 6150 is a chromium vanadium alloy with good ductility. This alloy is used in products when hardening is needed. This alloy has good resistance to shock and abrasion in heat treated condition.

The machinability rating of 6150 steel is 59.

Specifications:

• UNS G61500
• AISI 6150
• ASTM A231
• ASTM A505
• ASTM A29
• ASTM A322
• ASTM A331
• ASTM A519
• ASTM A752
• MIL SPEC MIL-S-8503
• SAE J1397
• SAE J404
• SAE J412

Applications:

Shafts, gears, pinions, hand tool components, aircraft parts, automotive leaf springs, piston rods, pump parts.

Speak to Next Generation Metals about alloy steel.

Stainless grade 304LV is the low-carbon variant of 304V, making it less susceptible to sensitization and more corrosion resistant when worked to high temperatures. This is Vacuum Arc Remelted (VAR), which produces a more uniform chemistry with minimal voids and contaminants.

The “L” refers to low carbon, so this would have less carbon than the 304V.

Specifications:

• ASTM A276
• ASME A580

Applications:

Catheters, guidewires, dentistry, medical, Neurostimulation, implant-dentistry, Orthopaedics, Vascular therapy

Stainless grade 304V wire is a commonly used alloy for non-implantable medical devices. This is Vacuum Arc Remelted (VAR), which produces a more uniform chemistry with minimal voids and contaminants. It can be used in corrosion environments and atmospheres with its excellent corrosion resistance.

304V is a flexible and robust stainless that is conducive to welding and soldering.

Forms:

Coil, Wire, Strip

Specifications:

• ASTM A313
• ASTM A666

Applications:

Catheters, stylets, guidewires, springs, needles. orthodontic arc wire, surgical instruments.

300M VAC-ARC Steel is a modified 4340 alloy steel with high hardenability and very high strength. This is achieved with the inclusion of vanadium and a higher silicon composition. 300M is a great choice where fracture toughness and impact strength are crucial. It is used mostly in the 270/300 KSI tensile strength range for aircraft gears, flap tracks and other structural applications.

Vacuum Arc Remelting (VAR) improved the cleanliness and preferred ingot structure.

This material is also called 4340 MOD VAC MELT.

Specifications:

• UNS K44220
• AMS 6257
• AMS 6417
• AMS 6419
• BMS-7-26
• DMS91935
• GM-1012
• ASTM A646
• ASTM A579
• MIL-S-8844

Applications:

Aircraft gears, flap tracks, high strength bolts, airframe parts, driveshafts, missile components,

9310 is a low alloy steel containing chromium, nickel and molybdenum with high hardenability, strength and fatigue resistance. 9310 is a deep hardening steel. It has excellent ductility and toughness make it optimal choice for components with heavy sections.

VIM-VAR 9310 is for parts requiring maximum strength, wear resistance and toughness.

9310 Aircraft Quality is vacuum arc remelted, resulting in the highest quality, cleanliness and reliability.

Specifications:

• AISI 9310
• UNS G93100
• UNS G93106
• AMS 6260
• AMS 6265
• AMS 6267
• ASTM A29 (E9310)
• ASTM A331 (E9310)
• ASTM A646 (9310)
• ASTM A322
• ASTM A519 (E9310)
• ASTM A711
• SAE J1397
• SAE J404

Applications:

Heavy duty gears, shafts, machined components, clutch parts, piston pins, chain roller and bushings, wrist pins, boring bars, cutting shanks, ratchets, power tools, aircraft engine gears, aircraft engine bearings, pinions, automotive applications, structural components, gears, rods, heat treatable shafts,

D6AC is a medium carbon, low alloy, vacuum melted ultra high-strength steel primarily used for high strength structural applications requiring strength levels up to 280,000 PSI.

Its hardenability of this alloy is better than of AISI 4340. D6AC is able to reach strengths ranging from 180 to 260 KSI through heat treatment.

D6AC VAC-ARC Steel is produced by the consumable electrode vacuum arc remelting process to provide optimum cleanliness and preferred ingot structure.

Specifications:

• UNS K24728
• AMS 6431
• AMS 6438
• AMS 6432
• AMS 6439
• AMS-S-8949
• ASTM A579
• MIL-S-8949
• FMS-1011 (General Dynamics)
• GM-1013 (Grumman)
• STM 05-500 (Lockheed)
• LCM 05-2190 (Lockheed)
• TL-428 (MAN Technology)

Applications:

Aircraft landing gear, axles, shafts.

See link: https://www.cartech.com/globalassets/datasheet-pdfs/d6ac.pdf

Next Generation Metals stocks seamless titanium tubing in its Chicago and Utah locations.

We stock prime material in many sizes in varying lengths in Grade 2 and Grade 9 titanium tube.

We carry this in 48″, 120″ and 144″ lengths.

We offer custom sizes.

Titanium tubing is commonly used golf clubs, heat exchangers, hydraulic lines, wheelchairs, chemical plants, oil and gas production, tennis rackets, lacrosse sticks, drive shaft tunnel supports, exhaust tubing, wheelie bars, suppressors, heat exchangers.

17-4 stainless steel ( Grade 630 ) Vac Melt

Specifications:

UNS S17400, AMS 5622, BMS-7-239

Applications: 

321 Vac Melt

Specifications:

UNS S32100 Specs 5-06020, ASTM A-240/240M, AMS 5510, AMS 5645, ASME SA-240, ASME SA-312, ASME SA-479, ASTM A-276 Condition A, , ASTM A-276 Condition S, ASTM A-479, QQ-S-763, QQ-S-766D.

410 Vac Melt Stainless is stocked in round bar.

Specifications:

UNS S41000, AMS 5611

Applications:

Fasteners, bolts, screws, bushings, nuts, shafts, pumps, valve components, gas and steam turbine components, press plates, gate valves.

Custom 450 is a martensitic age-hardening stainless steel that combines the very good corrosion resistance of 304 stainless and the moderate strength characteristics of 410 Air Melt Stainless.

Custom 450 is easy to fabricate and can be used in the annealed or hardened condition.

Specifications:

• UNS S45000
• AMS 5763
• AMS 5773
• AMS 5863 (Strip)
• ASTM A-564 (XM-25)
• ASME SA-564
• ASTM A959
• MR0175

Applications:

Medical instruments, small turbine engine shafts, extruder screws.

Jethete M152 is known for its very good toughness and creep rupture strength with a high temperature limit of 560*C. M152’s hardened and tempered martensitic stainless steel is usually use in highly stressed environments.

Jethlete M152 is creep and corrosion resistant, hardened and tempered with a high temperature limit.

Specifications:

• UNS S64152
• AMS 5718
• AMS 5719
• ASTM A-565 (XM-32)
• GE B50A948
• GE C50TF68A
• MSRR 6504
• MSRR 6514

Applications:

High heat bolts in aerospace applications, Gas turbine parts. Rings and structural components for land-based turbines, fasteners, drilling equipment, mechanical gears, aircraft landing gear, turbine blades, mechanical parts.

17-22A is a heat resistant steel that is characterized by high-strength and heat-resistant under high temperature, making it optimal for aircraft applications.

17-22A and 17-22A(S) comes in several forms, such as bar, forging and tubing.

17-22A(S) has higher carbon and chromium content then 17-22A.

These alloys have excellent machinability and toughness, in addition to resistance to high temperature oxidation.

Specifications:

UNS K14675, MIL S-24502, AISI 601

17-22A: AMS 6303, 6304, 6305, 6436

17-22A(S): AMS 6302, AMS 6385, AMS 6458

Applications: 

Grade 4130 Alloy Steel is a low alloy steel that contains molybdenum and chromium as its strengthening agents. The low carbon content of generally .30% is excellent for weldability. 4130 is able to be hardened by heat treatment. This allows it to reach a range of toughness. Features include good hardenability, strength, wear resistance, toughness and ductility.

Specifications:

UNS G41300, AMS 6345, AMS 6348, AMS 6350, AMS 6356, AMS 6360, AMS 6361, AMS 6370, AMS 6372, AMS 6371, AMS 6373, AMS-S-6758, ASTM-A-32, ASTM A322, ASTM 331, ASTM A505, ASTM A513, ASTM A519, ASTN A646, MIL-S-18729, MIL-S-16974, SAE J404, SAE J412, SAE J770, QQ-S-624 (for round bar)

Applications:

Aircraft engine mounts, ball and roller bearings, gears, rock-crushing machinery, automotive parts, cutting tools.

4140 alloy steel is a chromium molybdenum manganese alloy steel with good hardness penetration. 4140 has high fatigue strength, abrasion and impact resistance, toughness and torsional strength. This material was designed with consistent hardness and high strength.

4140 has good machinability in the annealed condition. It can also be welded using conventional techniques. Keep in mind that the mechanical properties of 4140 will be affected if its welded in the heat treated condition. So if you are going to weld it, heat treat it after welding.

Specifications:

AISI 4140, UNS G41400, AMS 6382, AMS-S-5626, AMS 6349, ASTM A193 (B7, B7M), AMS 6381, ASTM A194, ASTM A513, ASTM A829, AMS 6382, ASTM A29, SAE J1397, AMS 6390, ASTM A320, ASTM A519, SAE J404, AMS 6395, ASTM A322, ASTM A646, SA J412, AMS 6529, ASTM A331, ASTM A711

Applications:

Shafts, crankshaft, bolts, machinery parts, gears, milling spindle, nuts, slide, steel collet, steel conveyor and roll, steel coupling, drill collar, steel ejector, steel piston rod, steel stub, tool holders, couplings, guides, ejector pins, pump shafts, brake dies, spindles, sockets, motor shafts, forks, tracks, hydraulic machinery shafts, axles, tie rods, connecting rods, reamer bodies, chain links and sprockets.

4330V is a hardened and tempered high strength alloy steel. This high strength alloy has an exceptional low temperature impact properties.

Specifications:

UNS K23080, AMS 6411 (bar, forging, tubing), AMS 6427 (bar, forging, tubing), BMS-7-122, BMS-7-27, GM-1010, MIL-S-8699, AMS 2300, ASTM A-646,

Applications:

Applications in oil, gas and aerospace industries. Oil tools, drill jars, bolting, air frames.

52100 is a deep hardening alloy used for applications required at temps below 400 degrees. The 52100 VacMelt steel offers superior cleanliness and internal soundness over conventional air melted 52100.

52100 has exceptional resistance to wear and abrasion. This material is furnished in the spheroidized annealed condition in order to provide very good machinability.

Specifications:

UNS G52986, AMS 6444, AMS 6350, AMS 6370 (round bar), AMS 6371, AMS 6440, MIL-S-6758,M MIL-S-6739

Applications:

Aircraft bearings, bushings, gears, tools, anti-friction bearings, rollers, spacers, forming rolls, pins, spindles, precision instrument parts, seals, sleeves, engine parts, hydraulics parts, pump parts, clutch faces.

AISI 52100 is an alloy steel is a high carbon, chromium containing low alloy steel. 52100 can be machined using normal techniques. Machinability of 52100 in the annealed condition is good to machine by conventional methods, yet is has a very high hardness and abrasion resistance that can be developed by heat treatment to make the material suitable for extreme wear resistance applications.

E52100 is heat treatable.

52100 not omly comes in bar but also in tubing.

Specifications:

• UNS G52986
• AISI 52100
• ASTM A295,
• ASTM A519
• ASTM A535
• ASTM A646
• ASTM A711
• MIL SPEC MIL-S-980
• MIL SPEC MIL-S-7420
• MIL SPEC MIL-S-22141
• SAE J404,
• SAE J412
• SAE J770
• AMS 6440
• AMS 6441
• AMS 6444
• AMS 6447
• ASTM A322
• ASTM A331
• ASTM A505

Applications:

• Aircraft Bearings
• high stress parts
• bearing manufacture
• CV joints
• ball screws
• gauges,
• knives
• anti-friction bearings
• bushings
• sleeves
• dies
• gages
• molds
• tools,
• engine parts
• hydraulic parts
• pump parts
• clutch faces
• collets
• pins
• collars
• guides
• seals
• rollers

HP 9-4-20 is a low-alloy, high strength steel with a content of high nickel and cobalt to retain toughness. This alloy has good hardenability and weldability and very high fracture toughness. For HP 9-4-20 to keep its cleanliness, this is produced bu the consumable electrode vacuum arc remelting process.

has a Yield Strength of 200-205 KSI but can get brought up to 235KSI.

Specifications:

UNS K91461 (wire), K91472 (plate, sheet, strip, bar, forging, ring, tubing), AMS 6468, AMS 6523, AMS 6525, AMS A646,

Also known as Lescalloy

Applications: 

HP 9-4-30 is a low-alloy, high strength that is used in applications that need very high fracture toughness. This alloys tensile range is in the 220*240 KSI tensile range. JP 9-4-30 has a high nickel and cobalt content to promote its toughness. This alloy has been designed to have high hardenability, good weldability, and as mentioned before, excellent fracture toughness.

Specifications:

• UNS K91283
• AMS, 6524 (plate, sheet, strip)
• AMS 5626 (bar, forging, ring, tubing)
• BMS-7-182
• EMS-96247
• MMS-2102
• STO-160-LBO-012
• MIL-STD-2154 Class A

Also known as Lescalloy HP 9-4-30 VAC ARC.

Applications: 

Thank you for inquiring about Hy-Tuf material.

This is a high strength low alloy steel that has good ductility, impact strength and fracture toughness. This material has an addition of Molybdenum to help improve its toughness qualities. HY-TUF is used in the 220/240 ksi tensile strength range. It is VAR to provide optimum cleanliness and preferred ingot structure for superior mechanical properties.

This material is produced by VM/CVM followed by electroslag refining (ESR) and Vacuum Arc Melting (VAR)

This material is made in bar form, forging, rings, tubing and wire.

Specifications:

• UNS K32550
• ASTM A579 Grade 31
• AISI Hy-Tuf
• AMS 6418F
• AMS 6425
• DMS-1841 (Boeing)
• MIL-S-7108
• AMS-S-7108
• AMS 6453 (Wire)

Applications: 

M50 NIL comes in bars, forgings and tubing.

This material has good temper resistance that permits it to be used with a duplex treatment so that it obtains a good case depth and surface hardness in excess of 900 HV,.

Specifications:

• UNS K91231
• AMS 6278
• B50TF211
• AMS 6278
• CBS-50NIL

Applications:

• Aerospace bearings
• Gear assembly

Nitralloy N is low alloy nitriding steel. Nitriding N is able to be age hardened to extremely high strengths. At the same time this provides very high surface hardness through nitriding.

This grade is VAR (vacuum remelted) to improve microcleanliness that gives this alloy improved fatigue strength.

Specifications:

• UNS K52355
• AMS 6475
• BPS-299-947-042
• NitN

Applications:

• Aerospace
• Gears
• Rotorcraft industry.

Nickel 230 is a 99-99.999% pure nickel alloy alloy. The components of Nickel 230 is controlled to ensure uniform properties from the alloy for electronic use.

Specifications:

• UNS N02230

Applications:

• Cathode plates in electron tube applications.

Alloy 230 is a nickel=chromium-tungsten0molybdenum alloy which combines superb high temperature strength, oxidation and nitriding resistance and long term stability.

Alloy 230 has excellent oxidation resistance to 2100ºF and superior strength at this temperature.

Specifications:

• UNS N06230
• AMS 5878 (Plate)
• AMS 5891 (Bar)
• ASTM-B-572
• ASTM B435
• ASTM B622 (Seamless pipe and tube)
• ASTM B366
• ASTM B564

Applications:

• Transition ducts on turbine engines.
• Combustion linings on turbine engines.
• Furnace retorts.
• Flame shrouds
• Vacuum heat treat fixtures.
• Gas Turbines
• Thermal and petrochemical processing
• Heat Treating
• Ore and metal refining

Tungsten, a rare metal,  is one of the toughest elements that we find in nature. This is due to its density and high melting point.

Tungsten is 50 percent heavier than lead and twice the weight of steel. Tungsten is added to increase strength, hardness, elasticity and tensile strength.

Tungsten Carbide is a called a hard metal, although its a composite material with a very high hardness compared to other metals. Typically the hardness is 1600 HV. In its basic form tungsten is a fine gray powder but can be pressed and formed into different shapes. 

 Tungsten is an ultra fine grain material with very good wear resistance. 

Tungsten carbide has a melting point of 5,200°F and a boiling point of 10,830°F.

Specifications:

• UNS R07005
• AMS 7898/7899
• ASTM B760
• CAS 7440-33-7

Applications:

• Metal Machining
• Wear parts for mining and oil
• Metal forming tools
• cutting tips for saw blades
• wedding rings
• watch cases
• Ammunition
• trekking and ski poles
• Surgical Instruments
• Jewelry
• High temperature furnace components
• electronics
• welding electrodes

This corrosion and heat resistant material comes in tube form. This is an austenitic stainless steel that combines fine grain and stability in a varying range of temperatures. 19-9DL has good resistance to corrosion and brittle failure.

Specifications:

UNS S63198

AMS 5579

AMS 5526

ASTM A457

ASTM A477

ASTM A453

ASTM A458 Read the rest of this entry »

4142H steel is a chromium molybdenum alloy steel with good mechanical properties and toughness that will be improved after heat treatment.

Specifications:

• ASTM A304
• AISI 4142H
• UNS K11542
• SAE J1268
• AMS 6378

Applications:

• Die holders
• Flanges
• dies
• collets
• spindles
• acles
• cluth parts
• forming rolls
• machine tool components
• hand tools

Alloy 4750 / High Perm® is a nickel-iron alloy with the highest saturation flux density of any of the nickel-iron alloys, thus being a versatile alloy.

Specifications:

• UNS K94840
• AMS 7718
• ASTM A753 Alloy 2
• MIL-N-14411 Comp 3

Applications:

• Laminated cores for instrument transformers
• magnetic shields
• cores for electronic and communications devices

Specifications:

• UNS S42025
• X15TN ®
• ASTM F899
• AMS 5925
• DIN X40CrMoVN16-2)
• Chronifer ® M-15 KL

Applications:

• shear blades

ASTM F1058 is a cobalt-Chrommium-nickel-molybdenum alloy produced using a vacuum induction melting process that is followed by a electroslag remelting (VIM-ESR). Complying with the ASTM “F” spec, this material is biocompatible for surgical implants.

ASTM F1058 is compatible for magnetic resonance imaging sue to nonmagnetic properties.

Specifications:

UNS R30003

Also known as Phynox®, Elgiloy®, and Conichrome®

Wire: NACE MR0175 (ISO 15156-3), ISO 5832-7

Bar: AMS 5833, AMS 5834,

Applications:

Orthopedic wires and cables

Pacemaker lead conductors

Orthodontics

Stents

Surgical Clips

Human Implant Applications

Watchmaking

Inconel Alloy 825 is a nickel-iron-chromium alloy that contains small amounts of molybdenum, titanium and copper. Inconel 825 has great resistance to many corrosive environments, including pitting, crevice corrosion and stress-corrosion cracking.

Inconel 825 also has good mechanical properties from moderate to high temperatures.

Alloy 825 is similiar to Alloy 800 although it has improve resistance to aqueous corrosion.

Specifications:

UNS N08825

Applications:

Chemical Processing

Pollution Control

Propeller shafts

Tank trucks

Marine exhaust sytems

Oil and gas well piping

Nuclear fuel reprocessing

Acid production

AL6XN is a type of weldable stainless steel that is a low carbon, high purity, nitrogen-bearing super austenitic nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

This alloy has high strength and corrosion resistance that makes it a better choice than the conventional duplex stainless steels. It is commonly used instead of 300 series stainless steels in high temperature and low Ph applications.

Specifications:

• UNS N08367
• NACE MR0175
• ASTM B366
• ASTM B462
• ASTM B472
• ASTM B564
• ASTM B675
• ASTM B676
• ASTM B688
• ASTM B691
• ASTM B804

Applications:

Seawater Heat Exchangers

Offshore Oil and Gas Rigs

Distillation Columns

Chemical Processing

Medical Sterilization

P